By Mailys Laurent. Electrical Wiring. Publised at Monday, January 08th 2018, 00:13:06 AM. SMT fixtures are rigid PCB carriers that allow manufacturers to load single or multiple irregular boards, and then take them through the standard processing machines. This makes it possible to carry out tasks such as automatic mounting of electronic components, infra-red reflow soldering, wave soldering, automatic testing, etc.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 15:02:57 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By France Barbara. Car Wiring. Published at Thursday, December 28th 2017, 13:30:03 PM. Twist the bare ends together, then use pliers to press the twisted section into a compact shape. Solder the wires together so that they cannot be pulled apart, using only a little solder to avoid making the joint bulky. Wind insulating tape in a spiral over the joint.
By Dorian Yannic. Car Wiring. Published at Thursday, December 28th 2017, 11:54:02 AM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 11:33:40 AM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Fleurette Nina. Car Wiring. Published at Thursday, December 28th 2017, 11:30:31 AM. The electrical wiring in a car is a system of colour-coded wires called the loom. Where several wires run side by side they are bound together with insulating tape or plastic sleeving.
By Cyrille Lothaire. Electrical Wiring. Published at Thursday, December 28th 2017, 10:45:09 AM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Olivier Constance. Car Wiring. Published at Thursday, December 28th 2017, 10:09:08 AM. The electrical wiring in a car is a system of colour-coded wires called the loom. Where several wires run side by side they are bound together with insulating tape or plastic sleeving.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.