By Mailys Laurent. Electrical Wiring. Publised at Monday, January 01st 2018, 12:00:38 PM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 24th 2017, 00:10:58 AM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By Adrienne Emmanuel. Motor Wiring. Published at Saturday, September 23rd 2017, 20:20:29 PM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
By Fleurette Nina. Motor Wiring. Published at Thursday, September 21st 2017, 18:43:05 PM. Positioning servomechanisms were first used in military fire-control and marine navigation equipment. Today servomechanisms are used in automatic machine tools, satellite-tracking antennas, remote control airplanes, automatic navigation systems on boats and planes, and antiaircraft-gun control systems. Other examples are fly-by-wire systems in aircraft which use servos to actuate the aircraft control surfaces, and radio-controlled models which use RC servos for the same purpose. Many autofocus cameras also use a servomechanism to accurately move the lens. A hard disk drive has a magnetic servo system with sub-micrometre positioning accuracy. In industrial machines, servos are used to perform complex motion, in many applications.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 17th 2017, 03:23:46 AM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By France Barbara. Electrical Wiring. Published at Saturday, September 16th 2017, 00:10:12 AM. digital signal processor is a specialized microprocessor for the kind of algorithms employed in digital signal processing (DSP). The main goal is to accelerate the calculations while keeping the power consumption as low as possible. In this article, we review a basic addressing capability of DSP processors, i.e. circular buffering, which allows us to significantly accelerate the data transfer in a real-time system. Please note that since the acronym “DSP” stands for both “digital signal processing” and “digital signal processor," we will use the term “DSP processor” when referring to the hardware rather than the algorithm.
By Mailys Laurent. Motor Wiring. Published at Thursday, September 14th 2017, 20:19:13 PM. Speed control via a governor is another type of servomechanism. The steam engine uses mechanical governors; another early application was to govern the speed of water wheels. Prior to World War II the constant speed propeller was developed to control engine speed for maneuvering aircraft. Fuel controls for gas turbine engines employ either hydromechanical or electronic governing.
By Gaspard Magalie. Motor Wiring. Published at Monday, September 11th 2017, 19:50:47 PM. The motor can be directly pulsed by the arduino. The arduino can also supply power to the motor, but normally this is only a good idea for demonstration purposes. The arduino has a very weak power supply, and attempting to power a motor through it can destroy the arduino. Furthermore, the arduino may not be able to supply the exact correct maximum voltage. For this reason, an ESC is placed between the arduino and the motor.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.