By Mailys Laurent. Electrical Wiring. Publised at Monday, January 01st 2018, 12:00:38 PM. You can see how all the power supply connections use large traces or copper pours. The AWG doesn’t have high current requirements, but the board house doesn’t give you a discount for using less copper, so you might as well opt for large (= low-resistance, low-inductance) traces if you have the room.
By Olivier Constance. Electrical Wiring. Published at Friday, October 27th 2017, 15:32:39 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Cyrille Lothaire. Car Wiring. Published at Tuesday, October 24th 2017, 11:52:49 AM. Label wires before cutting them when working on a section of the loom. Before you disconnect anything, make absolutely sure you know how to put it back. Number both sides of each connection with labels made of masking tape. If necessary, make drawings of cable routes and how clips fit. Use a craft knife or razor blade to cut away the wrapping from the damaged section. Take care not to cut into the plastic cable insulation.
By Mailys Laurent. Motor Wiring. Published at Sunday, October 22nd 2017, 10:52:46 AM. RC servos are used to provide actuation for various mechanical systems such as the steering of a car, the control surfaces on a plane, or the rudder of a boat. Due to their affordability, reliability, and simplicity of control by microprocessors, they are often used in small-scale robotics applications. A standard RC receiver (or a microcontroller) sends pulse-width modulation (PWM) signals to the servo. The electronics inside the servo translate the width of the pulse into a position. When the servo is commanded to rotate, the motor is powered until the potentiometer reaches the value corresponding to the commanded position.
By Olivier Constance. Electrical Wiring. Published at Saturday, October 21st 2017, 10:27:32 AM. However, and this is very perplexing, there is no additional information related to the "separate application note." My suspicion is that Sensirion intended to include a link to this app note but then simply forgot to include it; perhaps additional information will be provided in the datasheet next revision.
By Claudine Nicolette. Car Wiring. Published at Friday, October 20th 2017, 09:41:36 AM. The damage caused by overheated wires is easy to find; but if only a single wire has overheated and melted at some point, you may have to use a circuit tester to find the break. If the damage is in an open run of wiring, you may be able to mend separate wires without taking out a section of the loom. If it is in any part of the covered sections, you need to remove at least part of the wiring loom.
By Adrienne Emmanuel. Motor Wiring. Published at Tuesday, October 17th 2017, 09:01:49 AM. These are also known as canned motors. Two wires go into them. They often are directly connected to a battery. A switch turns them on. Higher voltages cause them to spin faster. Often geared down in toys, they are designed to spin fast. If turned on and forced to not spin, the motor will heat up, and may even burn up. The motor is made by copper wire covered with clear paint, and wound together in a ball. When the motor heats up too much, the paint turns into smoke, nearby copper wires connect, the motor becomes weaker, the motor heats up more, more smoke comes out, etc. The winding resistance keeps going down. Measure the winding resistance when the motor is new and measure again when there are problems.
By Fleurette Nina. Electrical Wiring. Published at Thursday, October 12th 2017, 05:54:44 AM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.