By Mailys Laurent. Electrical Wiring. Publised at Tuesday, February 20th 2018, 03:43:49 AM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Claudine Nicolette. Electrical Wiring. Publised at Wednesday, February 21st 2018, 18:29:47 PM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Adrienne Emmanuel. Electrical Wiring. Published at Friday, December 29th 2017, 20:12:23 PM. You can see how all the power supply connections use large traces or copper pours. The AWG doesn’t have high current requirements, but the board house doesn’t give you a discount for using less copper, so you might as well opt for large (= low-resistance, low-inductance) traces if you have the room.
By Dorian Yannic. Electrical Wiring. Published at Friday, December 29th 2017, 15:30:43 PM. This IC is available only in an 8-pin dual-flat no-leads (DFN) package, measuring a scant 2.5mm × 2.5mm with a tiny thickness of only 0.9mm. There is also, in addition to the eight pins, a thermal pad that is connected to ground (see image below).
By Mailys Laurent. Electrical Wiring. Published at Friday, December 29th 2017, 09:43:55 AM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Fleurette Nina. Motor Wiring. Published at Friday, December 29th 2017, 08:52:17 AM. After the retaining ring is removed, the entire assembly that spins can be removed. There may be some resistance that feels like removing magnets from each other. Underneath the cup of all outrunner brushless motors is a series of coils. On some motors, between the coils, are hall effect probes. Hall effect probes detect the spinning magnetic field and provide a pulse out of the brushless motors to the electronics. From this pulse the electronics can precisely control the speed of the motor
By Dorian Yannic. Motor Wiring. Published at Friday, December 29th 2017, 07:22:49 AM. Servomotors are used for both high-end and low-end applications. On the high end are precision industrial components that use a rotary encoder. On the low end are inexpensive radio control servos (RC servos) used in radio-controlled models which use a free-running motor and a simple potentiometer position sensor with an embedded controller. The term servomotor generally refers to a high-end industrial component while the term servo is most often used to describe the inexpensive devices that employ a potentiometer. Stepper motors are not considered to be servomotors, although they too are used to construct larger servomechanisms. Stepper motors have inherent angular positioning, owing to their construction, and this is generally used in an open-loop manner without feedback. They are generally used for medium-precision applications.
By Fleurette Nina. Electrical Wiring. Published at Friday, December 29th 2017, 07:16:00 AM. Since the finite-impulse-response (FIR) filtering is a common operation in DSP, we will continue our discussion based on examining the difference equation of an FIR filter. This simple example will show the typical properties of many DSP algorithms. After reviewing the problem of handling the incoming samples, we will discuss the circular buffering as an efficient solution to the problem.
By Cyrille Lothaire. Car Wiring. Published at Friday, December 29th 2017, 05:12:16 AM. Relays are devices that utilize a central iron core fitted closely to the inside of a coil of wire. When the wire is energized the iron core will be drawn down the length of the coil, the direction dependent upon the direction of current flow. If the relays iron core is fitted with large, high current-carrying contacts it can be used as a high-current switch. Relays are used throughout cars for horns, electric fans, air conditioning clutches, etc. and the most important one is the starter solenoid.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.