By Mailys Laurent. Electrical Wiring. Publised at Thursday, January 18th 2018, 03:27:31 AM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By Claudine Nicolette. Electrical Wiring. Publised at Wednesday, February 21st 2018, 18:29:47 PM. SMT fixtures are rigid PCB carriers that allow manufacturers to load single or multiple irregular boards, and then take them through the standard processing machines. This makes it possible to carry out tasks such as automatic mounting of electronic components, infra-red reflow soldering, wave soldering, automatic testing, etc.
By Mailys Laurent. Electrical Wiring. Publised at Tuesday, February 20th 2018, 03:43:49 AM. The fixture should support the board and prevent distortion as the board goes through the printing, component placement, and reflow processes. Its construction should ensure adequate protection for the bottom side components during the double-sided reflow process.
By Gaspard Magalie. Motor Wiring. Published at Sunday, December 31st 2017, 07:42:08 AM. Servomotors are used for both high-end and low-end applications. On the high end are precision industrial components that use a rotary encoder. On the low end are inexpensive radio control servos (RC servos) used in radio-controlled models which use a free-running motor and a simple potentiometer position sensor with an embedded controller. The term servomotor generally refers to a high-end industrial component while the term servo is most often used to describe the inexpensive devices that employ a potentiometer. Stepper motors are not considered to be servomotors, although they too are used to construct larger servomechanisms. Stepper motors have inherent angular positioning, owing to their construction, and this is generally used in an open-loop manner without feedback. They are generally used for medium-precision applications.
By Mailys Laurent. Motor Wiring. Published at Sunday, December 31st 2017, 05:19:37 AM. Parts of the motor are often attached to a circuit board. Magnets are attached on the inside of the can that spins with the shaft .. sort of like a spinning umbrella. All brushless motors have a spinning umbrella. Inside the umbrella is a permanent magnet. It looks like one continuous round magnet. However it is more like series of magnets.
By Dorian Yannic. Motor Wiring. Published at Sunday, December 31st 2017, 04:44:25 AM. Speed can be varied by either changing the voltage or pulsing the motor. Most computer controlled DC motors are pulsed. Pulses of a fixed voltage are sent to the motor, usually by an Electronic Speed Controller or ESC. A pulse of 1.5 ms causes no motion. Wider pulses cause faster spinning in one direction. Shorter pulses cause faster spinning in the opposite direction. Eventually, an overstressed ESC stops pulsing and turns one wire on and one wire off, depending on the direction.
By Fleurette Nina. Electrical Wiring. Published at Sunday, December 31st 2017, 02:18:44 AM. When implementing a real-time system, we find a circular buffer critical whether we are using a DSP processor or a general purpose processor (GPP). However, with a GPP we may have to implement the circular buffer in software. As discussed in the previous section, with each new sample, we have to update the pointer which contains the address of the newest sample. With a circular buffer implemented in software, the programmer needs to take care of updating the buffer pointers after each read and write operation. When the pointer reaches the end of the buffer, the program must wrap the pointer back to the beginning of the buffer.
By Olivier Constance. Car Wiring. Published at Sunday, December 31st 2017, 00:36:48 AM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Fleurette Nina. Motor Wiring. Published at Saturday, December 30th 2017, 23:49:44 PM. Brushless inrunners are very similar from the outside to a brushed DC motor in terms of size. They are usually mounted on a circuit board like a servo motor with a gear box. They spin very fast and have to be geared down like a brushed dc motor. They are different than a brushed dc motor in that they are stronger, more efficient and last longer. They can be matched to a wider variety of propellers or loads by adjusting the gearing.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, December 30th 2017, 22:36:59 PM. Brushless inrunners are very similar from the outside to a brushed DC motor in terms of size. They are usually mounted on a circuit board like a servo motor with a gear box. They spin very fast and have to be geared down like a brushed dc motor. They are different than a brushed dc motor in that they are stronger, more efficient and last longer. They can be matched to a wider variety of propellers or loads by adjusting the gearing.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.