By Cyrille Lothaire. Car Wiring. Publised at Friday, January 05th 2018, 19:31:18 PM. Spade terminal The spade terminal is theusual way of fixing wires to components. Crimp or bullet connector The crimpconnector is used for joining single wires toeach other. It may be a single or doubleconnector, or a multi- connector carryingseveral wires.
By Gaspard Magalie. Electrical Wiring. Published at Saturday, December 30th 2017, 21:46:15 PM. The fixtures are usually available in a variety of designs, materials, sizes, and thicknesses. Some can carry more than one board hence allowing the processing of multiple PCBs simultaneously. Other designs have adjustments to support both the primary and secondary side processes.
By Mailys Laurent. Electrical Wiring. Published at Saturday, December 30th 2017, 21:23:01 PM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 19:12:00 PM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Dorian Yannic. Motor Wiring. Published at Saturday, December 30th 2017, 17:51:58 PM. Brushless outrunners are always built on a circuit board. This makes them cheaper. The circuit board for this CD motor has no electronics on it. A ribbon cable attaches 11 wires to another controller circuit board. But often the controller is built onto the same circuit board. The circuit boards interface with a controller in two ways.
By Claudine Nicolette. Car Wiring. Published at Saturday, December 30th 2017, 16:22:53 PM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Fleurette Nina. Car Wiring. Published at Saturday, December 30th 2017, 15:34:30 PM. The electrical wiring in a car is a system of colour-coded wires called the loom. Where several wires run side by side they are bound together with insulating tape or plastic sleeving.
By Gaspard Magalie. Motor Wiring. Published at Saturday, December 30th 2017, 13:07:39 PM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.