By Cyrille Lothaire. Car Wiring. Publised at Sunday, February 25th 2018, 04:10:29 AM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Claudine Nicolette. Car Wiring. Publised at Saturday, February 17th 2018, 04:34:39 AM. If this does not blow a fuse the wiring overheats and melts insulation, perhaps starting a fire. A similar result can come from fitting accessories incorrectly, or if power demand is too high for the size of the wire being used. After many years, insulation may become hard and brittle, particularly where it is exposed to heat, as in the engine bay. Sections, or all of the loom, may need replacing.
By Olivier Constance. Electrical Wiring. Published at Friday, October 27th 2017, 15:32:39 PM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By Cyrille Lothaire. Car Wiring. Published at Tuesday, October 24th 2017, 11:52:49 AM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Mailys Laurent. Motor Wiring. Published at Sunday, October 22nd 2017, 10:52:46 AM. Electronic motors are found in kids toys, RC cars, airplanes and helicopters, printers, scanners, and fax machines. They are expensive when purchased, quantity 1, new with manual. This is because the motors are part of a supply chain that is usually just making enough to fill orders for kids toys, etc. Many can be found for sale on the internet, but very few are in stock and the price is high if they are. Often it is easier to purchase the kids toy and take it apart. The goal is to connect these motors to the arduino and then make something new with them. The goal of this document is to describe what to expect.
By Olivier Constance. Electrical Wiring. Published at Saturday, October 21st 2017, 10:27:32 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Claudine Nicolette. Car Wiring. Published at Friday, October 20th 2017, 09:41:36 AM. Wires and bundles of wires are clipped to the bodywork to keep them out of the way. Where they run through a hole, the sharp edges are lined with a rubber grommet. Sometimes the loom is divided into sections joined by multi-pin plugs and sockets, so that it can be removed and refitted section by section.
By Adrienne Emmanuel. Motor Wiring. Published at Tuesday, October 17th 2017, 09:01:49 AM. Stepper motors are like a servo motor in that they move to a spot and hold their position. But they can also spin like a DC and Brushless Motor. They can not hold their position as strongly as a servo motor, and they can not spin as fast as a brushed or brushless motor.
By Fleurette Nina. Electrical Wiring. Published at Thursday, October 12th 2017, 05:54:44 AM. There are different panelization and de-panelization methods depending on the application of the PCB, thickness, shape, component layout, type of edges, and other factors. The two popular methods are the V-groove panelization and the breakaway tab panelization. Each of these uses a different method to separate the boards from the main array and has its advantages and limitations.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.