By Olivier Constance. Car Wiring. Publised at Thursday, January 04th 2018, 06:05:59 AM. The damage caused by overheated wires is easy to find; but if only a single wire has overheated and melted at some point, you may have to use a circuit tester to find the break. If the damage is in an open run of wiring, you may be able to mend separate wires without taking out a section of the loom. If it is in any part of the covered sections, you need to remove at least part of the wiring loom.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 07:48:26 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Fleurette Nina. Motor Wiring. Published at Thursday, December 28th 2017, 05:54:53 AM. This means that when the next electromagnet is turned on and the first is turned off, the gear rotates slightly to align with the next one. From there the process is repeated. Each of those rotations is called a "step", with an integer number of steps making a full rotation. In that way, the motor can be turned by a precise angle.
By Fleurette Nina. Electrical Wiring. Published at Thursday, December 28th 2017, 05:52:53 AM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Mailys Laurent. Electrical Wiring. Published at Thursday, December 28th 2017, 05:20:31 AM. However, the SMT components and the traces must be at least 3.00 mm from the perforation holes. This prevents the damage to the PCB or components which can occur due to surface stress and splinter when separating the boards. One drawback with this method is that it may leave some unwanted board protrusions on the edges.
By Cyrille Lothaire. Electrical Wiring. Published at Thursday, December 28th 2017, 05:00:05 AM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Adrienne Emmanuel. Car Wiring. Published at Thursday, December 28th 2017, 03:09:28 AM. When the clutch pedal is released, the thrust bearing is withdrawn and the diaphragm-spring load once again clamps the driven plate to the flywheel to resume the transmission of power. Some cars have a hydraulically operated clutch. Pressure on the clutch pedal inside the car activates a piston in a master cylinder, which transmits the pressure through a fluid-filled pipe to a slave cylinder mounted on the clutch housing. The slave-cylinder piston is connected to the clutch release arm.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 00:08:10 AM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.