By Claudine Nicolette. Car Wiring. Publised at Friday, December 29th 2017, 01:22:14 AM. Push the wire into the connector so that the strands just protrude from the round end. Grip the cable, connector uppermost, in a vice or self-locking pliers, so that the connector rests on top of the vice and cannot slide down the wire when soldering. Inside a bullet connector. Apply solder on the top of the connector, and let it melt and run down inside. Trim off the protruding strands with wire cutters.
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 19:12:00 PM. There are different panelization and de-panelization methods depending on the application of the PCB, thickness, shape, component layout, type of edges, and other factors. The two popular methods are the V-groove panelization and the breakaway tab panelization. Each of these uses a different method to separate the boards from the main array and has its advantages and limitations.
By Dorian Yannic. Motor Wiring. Published at Saturday, December 30th 2017, 17:51:58 PM. Speed control via a governor is another type of servomechanism. The steam engine uses mechanical governors; another early application was to govern the speed of water wheels. Prior to World War II the constant speed propeller was developed to control engine speed for maneuvering aircraft. Fuel controls for gas turbine engines employ either hydromechanical or electronic governing.
By Claudine Nicolette. Car Wiring. Published at Saturday, December 30th 2017, 16:22:53 PM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Fleurette Nina. Car Wiring. Published at Saturday, December 30th 2017, 15:34:30 PM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Gaspard Magalie. Motor Wiring. Published at Saturday, December 30th 2017, 13:07:39 PM. These are also known as canned motors. Two wires go into them. They often are directly connected to a battery. A switch turns them on. Higher voltages cause them to spin faster. Often geared down in toys, they are designed to spin fast. If turned on and forced to not spin, the motor will heat up, and may even burn up. The motor is made by copper wire covered with clear paint, and wound together in a ball. When the motor heats up too much, the paint turns into smoke, nearby copper wires connect, the motor becomes weaker, the motor heats up more, more smoke comes out, etc. The winding resistance keeps going down. Measure the winding resistance when the motor is new and measure again when there are problems.
By Fleurette Nina. Electrical Wiring. Published at Saturday, December 30th 2017, 11:42:26 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Fleurette Nina. Electrical Wiring. Published at Saturday, December 30th 2017, 11:28:42 AM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.