By Fleurette Nina. Car Wiring. Publised at Friday, December 29th 2017, 03:06:25 AM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, October 04th 2017, 00:20:15 AM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Mailys Laurent. Electrical Wiring. Published at Monday, October 02nd 2017, 21:00:02 PM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, October 01st 2017, 20:21:48 PM. The ease of loading and unloading the PCBs, as well as the ability to handle multiple PCBs, are important in high production lines. In addition, fixtures should provide thermal protection to the heat sensitive areas of the PCB.
By Dorian Yannic. Electrical Wiring. Published at Saturday, September 30th 2017, 19:13:18 PM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Adrienne Emmanuel. Car Wiring. Published at Wednesday, September 27th 2017, 18:52:26 PM. Spade terminal The spade terminal is theusual way of fixing wires to components. Crimp or bullet connector The crimpconnector is used for joining single wires toeach other. It may be a single or doubleconnector, or a multi- connector carryingseveral wires.
By Gaspard Magalie. Electrical Wiring. Published at Tuesday, September 26th 2017, 17:22:48 PM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 24th 2017, 00:10:58 AM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.