By Gaspard Magalie. Car Wiring. Publised at Saturday, January 06th 2018, 02:18:13 AM. Spade terminal The spade terminal is theusual way of fixing wires to components. Crimp or bullet connector The crimpconnector is used for joining single wires toeach other. It may be a single or doubleconnector, or a multi- connector carryingseveral wires.
By Dorian Yannic. Electrical Wiring. Published at Saturday, September 30th 2017, 19:13:18 PM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Adrienne Emmanuel. Car Wiring. Published at Wednesday, September 27th 2017, 18:52:26 PM. If this does not blow a fuse the wiring overheats and melts insulation, perhaps starting a fire. A similar result can come from fitting accessories incorrectly, or if power demand is too high for the size of the wire being used. After many years, insulation may become hard and brittle, particularly where it is exposed to heat, as in the engine bay. Sections, or all of the loom, may need replacing.
By Gaspard Magalie. Electrical Wiring. Published at Tuesday, September 26th 2017, 17:22:48 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 24th 2017, 00:10:58 AM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Adrienne Emmanuel. Motor Wiring. Published at Saturday, September 23rd 2017, 20:20:29 PM. The two wires of the brushed dc motor can be thought of as forward and reverse. The three wires of brushless can be thought of as 1, 2 and 3. Going forward would be this sequence 1-2, 2-3, 3-1, 1-2, etc. Going backwards would be 1-3, 3-2, 2-1, 1-3, etc. What this means is that one third of the motor is helping maintain momentum while another third is pulling the motor in a new direction.
By Fleurette Nina. Motor Wiring. Published at Thursday, September 21st 2017, 18:43:05 PM. The circular arrangement of electromagnets is divided into groups, each group called a phase, and there is an equal number of electromagnets per group. The number of groups is chosen by the designer of the stepper motor. The electromagnets of each group are interleaved with the electromagnets of other groups to form a uniform pattern of arrangement. For example, if the stepper motor has two groups identified as A or B, and ten electromagnets in total, then the grouping pattern would be ABABABABAB.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 17th 2017, 03:23:46 AM. However, and this is very perplexing, there is no additional information related to the "separate application note." My suspicion is that Sensirion intended to include a link to this app note but then simply forgot to include it; perhaps additional information will be provided in the datasheet next revision.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.