By Claudine Nicolette. Car Wiring. Publised at Friday, December 29th 2017, 01:22:14 AM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Claudine Nicolette. Car Wiring. Published at Saturday, December 30th 2017, 16:22:53 PM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Fleurette Nina. Car Wiring. Published at Saturday, December 30th 2017, 15:34:30 PM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Gaspard Magalie. Motor Wiring. Published at Saturday, December 30th 2017, 13:07:39 PM. Brushed DC motors rotate continuously when DC voltage is applied to their terminals. The stepper motor is known by its property to convert a train of input pulses (typically square wave pulses) into a precisely defined increment in the shaft position. Each pulse moves the shaft through a fixed angle. Stepper motors effectively have multiple "toothed" electromagnets arranged around a central gear-shaped piece of iron. The electromagnets are energized by an external driver circuit or a micro controller. To make the motor shaft turn, first, one electromagnet is given power, which magnetically attracts the gear teeth. When the gear teeth are aligned to the first electromagnet, they are slightly offset from the next electromagnet.
By Fleurette Nina. Electrical Wiring. Published at Saturday, December 30th 2017, 11:42:26 AM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By Fleurette Nina. Electrical Wiring. Published at Saturday, December 30th 2017, 11:28:42 AM. This IC is available only in an 8-pin dual-flat no-leads (DFN) package, measuring a scant 2.5mm × 2.5mm with a tiny thickness of only 0.9mm. There is also, in addition to the eight pins, a thermal pad that is connected to ground (see image below).
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 09:22:32 AM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By Olivier Constance. Car Wiring. Published at Saturday, December 30th 2017, 08:37:15 AM. Push the wire into the connector so that the strands just protrude from the round end. Grip the cable, connector uppermost, in a vice or self-locking pliers, so that the connector rests on top of the vice and cannot slide down the wire when soldering. Inside a bullet connector. Apply solder on the top of the connector, and let it melt and run down inside. Trim off the protruding strands with wire cutters.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.