By Olivier Constance. Car Wiring. Publised at Thursday, January 04th 2018, 06:05:59 AM. If this does not blow a fuse the wiring overheats and melts insulation, perhaps starting a fire. A similar result can come from fitting accessories incorrectly, or if power demand is too high for the size of the wire being used. After many years, insulation may become hard and brittle, particularly where it is exposed to heat, as in the engine bay. Sections, or all of the loom, may need replacing.
By France Barbara. Electrical Wiring. Published at Sunday, November 12th 2017, 22:18:25 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Dorian Yannic. Electrical Wiring. Published at Saturday, November 11th 2017, 11:56:59 AM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By Dorian Yannic. Motor Wiring. Published at Friday, November 10th 2017, 03:07:38 AM. Fixed speed motors have a cable that contains power, inputs (motor on, motor half speed) and an output pulse related to the motors motion. Variable speed motors typically have no circuitry directly associated with the motor. Instead there are typically three wires coming out that attach to an "Electronic Speed Controller."
By France Barbara. Electrical Wiring. Published at Tuesday, November 07th 2017, 00:10:46 AM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Gaspard Magalie. Motor Wiring. Published at Monday, November 06th 2017, 04:29:01 AM. One way to distinguish the center tap (common wire) from a coil-end wire is by measuring the resistance. Resistance between common wire and coil-end wire is always half of the resistance between coil-end wires. This is because there is twice the length of coil between the ends and only half from center (common wire) to the end. A quick way to determine if the stepper motor is working is to short circuit every two pairs and try turning the shaft. Whenever a higher than normal resistance is felt, it indicates that the circuit to the particular winding is closed and that the phase is working.
By Olivier Constance. Electrical Wiring. Published at Thursday, November 02nd 2017, 20:16:28 PM. Care should be taken when depaneling the perforated-tab PCB array; otherwise, an incorrect method will splinter or tear the solder-mask or active surface layer. The ideal breakout method should not cause any damage to the board or transfer stress from the PCB surface to the components.
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 31st 2017, 22:07:54 PM. digital signal processor is a specialized microprocessor for the kind of algorithms employed in digital signal processing (DSP). The main goal is to accelerate the calculations while keeping the power consumption as low as possible. In this article, we review a basic addressing capability of DSP processors, i.e. circular buffering, which allows us to significantly accelerate the data transfer in a real-time system. Please note that since the acronym “DSP” stands for both “digital signal processing” and “digital signal processor," we will use the term “DSP processor” when referring to the hardware rather than the algorithm.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.