By Gaspard Magalie. Car Wiring. Publised at Saturday, January 06th 2018, 02:18:13 AM. Relays are devices that utilize a central iron core fitted closely to the inside of a coil of wire. When the wire is energized the iron core will be drawn down the length of the coil, the direction dependent upon the direction of current flow. If the relays iron core is fitted with large, high current-carrying contacts it can be used as a high-current switch. Relays are used throughout cars for horns, electric fans, air conditioning clutches, etc. and the most important one is the starter solenoid.
By Claudine Nicolette. Car Wiring. Published at Friday, October 20th 2017, 09:41:36 AM. Cable sizes are given by two numbers. The first one is the number of strands. The second (which is always the same in car wiring) is the diameter of each strand in millimetres. Twisting wires together and fitting spade terminals twist bare ends together and solder them.Cover the joint with insulating tape. Tag connectors are closedround the bare wire withpliers, then soldered. A spade terminal is easy to disconnect andreconnect. Methods of joining, wires To connect two wires, use a wire stripper to remove about in. (19 mm) of insulation from each wire.
By Adrienne Emmanuel. Motor Wiring. Published at Tuesday, October 17th 2017, 09:01:49 AM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
By Fleurette Nina. Electrical Wiring. Published at Thursday, October 12th 2017, 05:54:44 AM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 10th 2017, 02:36:22 AM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Claudine Nicolette. Motor Wiring. Published at Saturday, October 07th 2017, 00:23:28 AM. The circular arrangement of electromagnets is divided into groups, each group called a phase, and there is an equal number of electromagnets per group. The number of groups is chosen by the designer of the stepper motor. The electromagnets of each group are interleaved with the electromagnets of other groups to form a uniform pattern of arrangement. For example, if the stepper motor has two groups identified as A or B, and ten electromagnets in total, then the grouping pattern would be ABABABABAB.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, October 04th 2017, 00:20:15 AM. To overcome these challenges, engineers may use SMT fixtures or the panelization techniques. Each of the two methods provides a carrier with standard dimensions and provisions for fitting, securing and supporting the irregular boards.
By Mailys Laurent. Electrical Wiring. Published at Monday, October 02nd 2017, 21:00:02 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.