By Fleurette Nina. Car Wiring. Publised at Thursday, December 28th 2017, 11:30:31 AM. Label wires before cutting them when working on a section of the loom. Before you disconnect anything, make absolutely sure you know how to put it back. Number both sides of each connection with labels made of masking tape. If necessary, make drawings of cable routes and how clips fit. Use a craft knife or razor blade to cut away the wrapping from the damaged section. Take care not to cut into the plastic cable insulation.
By Fleurette Nina. Car Wiring. Published at Wednesday, February 14th 2018, 19:26:51 PM. Use insulating tape in a spiral to bind wires together. If you have to lead a new wire along a difficult route - to the rear of the car, for example - you could take the opportunity to lead a spare wire at the same time, for any accessory you might want to fit later. Cover the end of a spare wire with insulating tape to prevent an electrical short circuit. Identifying cable sizes 14/30 cable 65/30 cable High-tension (HT) lead The starter cable Types of cable.
By Gaspard Magalie. Car Wiring. Published at Wednesday, February 14th 2018, 13:54:05 PM. Cars are filled with stuff that can make or break performance. The engine needs to be fed the proper amounts of air, fuel, and spark. The suspension and brakes must be in tip-top shape. The wheels and tires, transmission, cooling system, gauges—even the seats—must all function properly.
By Claudine Nicolette. Motor Wiring. Published at Wednesday, February 14th 2018, 13:26:18 PM. Brushless inrunners are very similar from the outside to a brushed DC motor in terms of size. They are usually mounted on a circuit board like a servo motor with a gear box. They spin very fast and have to be geared down like a brushed dc motor. They are different than a brushed dc motor in that they are stronger, more efficient and last longer. They can be matched to a wider variety of propellers or loads by adjusting the gearing.
By Fleurette Nina. Car Wiring. Published at Wednesday, February 14th 2018, 07:06:57 AM. The starter solenoid has very large contacts to carry the batterys full current. Its wire coil is actuated by a smaller current from the ignition switch, at which time the iron core slams down to make contact and turn on the starter motor. Most non-Ford starter motors employ a solenoid built into the motor itself. This type of solenoid not only provides the motors electrical power but also mechanically engages the starters drive gear onto the flywheel.
By Adrienne Emmanuel. Motor Wiring. Published at Wednesday, February 14th 2018, 06:58:56 AM. Speed can be varied by either changing the voltage or pulsing the motor. Most computer controlled DC motors are pulsed. Pulses of a fixed voltage are sent to the motor, usually by an Electronic Speed Controller or ESC. A pulse of 1.5 ms causes no motion. Wider pulses cause faster spinning in one direction. Shorter pulses cause faster spinning in the opposite direction. Eventually, an overstressed ESC stops pulsing and turns one wire on and one wire off, depending on the direction.
By Adrienne Emmanuel. Car Wiring. Published at Tuesday, February 13th 2018, 20:19:44 PM. Even if only one wire has overheated, inspect all the others to make sure their insulation is not damaged. Before cutting out damaged wires, make sure that the colour coding is the same at each end of the damaged section of each wire, and that it is not so discoloured that it is unrecognisable. If there is any chance of confusion, label both ends.
By Mailys Laurent. Car Wiring. Published at Tuesday, February 13th 2018, 18:46:51 PM. Use a 25-65 watt iron for most work, and a 150-250 watt one for large cables, or an 8 oz (225 g) gas-heated iron. Working safelyDisconnect both terminals of the battery before doing any work on wiring other than testing. Whenever you work on the car, watch for any part of the loom coming loose from its clips, for there is a risk of it getting trapped or burned. Always replace wiring in its clips.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.