By Claudine Nicolette. Car Wiring. Publised at Tuesday, January 02nd 2018, 15:21:04 PM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Mailys Laurent. Motor Wiring. Published at Sunday, December 31st 2017, 05:19:37 AM. Fixed speed motors have a cable that contains power, inputs (motor on, motor half speed) and an output pulse related to the motors motion. Variable speed motors typically have no circuitry directly associated with the motor. Instead there are typically three wires coming out that attach to an "Electronic Speed Controller."
By Dorian Yannic. Motor Wiring. Published at Sunday, December 31st 2017, 04:44:25 AM. A servomotor is a specific type of motor that is combined with a rotary encoder or a potentiometer to form a servomechanism. This assembly may in turn form part of another servomechanism. A potentiometer provides a simple analog signal to indicate position, while an encoder provides position and usually speed feedback, which by the use of a PID controller allow more precise control of position and thus faster achievement of a stable position (for a given motor power). Potentiometers are subject to drift when the temperature changes whereas encoders are more stable and accurate.
By Fleurette Nina. Electrical Wiring. Published at Sunday, December 31st 2017, 02:18:44 AM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Olivier Constance. Car Wiring. Published at Sunday, December 31st 2017, 00:36:48 AM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Fleurette Nina. Motor Wiring. Published at Saturday, December 30th 2017, 23:49:44 PM. The outrunner is already the standard motor in laser printers, copy machines, fax machines, scanners, blue ray players, cd players, where a very precise, constant speed is needed. It is also found in model helicopters, RC airplanes and other variable speed applications where there are light weight requirements. It is totally different than all other motors.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, December 30th 2017, 22:36:59 PM. Servomotors are used for both high-end and low-end applications. On the high end are precision industrial components that use a rotary encoder. On the low end are inexpensive radio control servos (RC servos) used in radio-controlled models which use a free-running motor and a simple potentiometer position sensor with an embedded controller. The term servomotor generally refers to a high-end industrial component while the term servo is most often used to describe the inexpensive devices that employ a potentiometer. Stepper motors are not considered to be servomotors, although they too are used to construct larger servomechanisms. Stepper motors have inherent angular positioning, owing to their construction, and this is generally used in an open-loop manner without feedback. They are generally used for medium-precision applications.
By Gaspard Magalie. Electrical Wiring. Published at Saturday, December 30th 2017, 21:46:15 PM. Depanelization is the process of separating the individual boards from the main array and usually depends on the panelization method applied. The choice depends on the clearance to provide at the edges of the PCB, and the presence of sensitive SMT devices, or hanging connectors near the edges. There are automatic methods, such as the laser cutting or depaneling router, as well as manual methods that involve breaking the tabs using hands or other tools.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.