By Olivier Constance. Car Wiring. Publised at Thursday, January 04th 2018, 06:05:59 AM. Several modern cars have separate thin wires embedded in flat plastic strips. These strips are very compact, and are used mainly for accessories and relay controls that require little power.
By Adrienne Emmanuel. Motor Wiring. Published at Friday, December 29th 2017, 03:09:39 AM. 2 wires. Servomechanisms are designed to move to a spot and hold it is position. They are not designed to spin continuously. Used to position print heads in ink jet printers, plotters, scanners. Travel at set speeds. Go to a spot and stop. When stopped and still turned on, will attempt to hold it is position. Forcing it to move in this position can damage the motor. Typically is controlled by a circuit board that counts shadows with an LED and light sensor or has a resistor that changes value depending upon position. Often zooms to one side when powered on to figure out where it is at.
By Fleurette Nina. Car Wiring. Published at Friday, December 29th 2017, 03:06:25 AM. Push the wire into the connector so that the strands just protrude from the round end. Grip the cable, connector uppermost, in a vice or self-locking pliers, so that the connector rests on top of the vice and cannot slide down the wire when soldering. Inside a bullet connector. Apply solder on the top of the connector, and let it melt and run down inside. Trim off the protruding strands with wire cutters.
By Claudine Nicolette. Car Wiring. Published at Friday, December 29th 2017, 01:22:14 AM. Use a 25-65 watt iron for most work, and a 150-250 watt one for large cables, or an 8 oz (225 g) gas-heated iron. Working safelyDisconnect both terminals of the battery before doing any work on wiring other than testing. Whenever you work on the car, watch for any part of the loom coming loose from its clips, for there is a risk of it getting trapped or burned. Always replace wiring in its clips.
By Dorian Yannic. Car Wiring. Published at Friday, December 29th 2017, 00:08:27 AM. Brushes are used to create electrical contact to the commutator segments and when current is fed into two of the four brushes, it flows through all the loops of the armature and shoe windings and out the other two brushes. This creates a magnetic field around each loop. As the armature turns, the loop will move to a position where the current flow reverses. This constant reversal of current flow allows the armature and field coils to repel each other and spin the motor. The greater the current flowing in the coils, the greater the magnetic forces, and the greater the power of the motor.
By Adrienne Emmanuel. Electrical Wiring. Published at Thursday, December 28th 2017, 21:36:39 PM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 21:29:40 PM. Depanelization is the process of separating the individual boards from the main array and usually depends on the panelization method applied. The choice depends on the clearance to provide at the edges of the PCB, and the presence of sensitive SMT devices, or hanging connectors near the edges. There are automatic methods, such as the laser cutting or depaneling router, as well as manual methods that involve breaking the tabs using hands or other tools.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 21:14:12 PM. In a demanding application, we may not have the time to continuously check the pointers to see if they have reached the end of the buffer and wrap them back to the beginning of the buffer when necessary. As a result, a DSP processor uses dedicated hardware to provide some fast circular buffers.This hardware implementation automatically checks the status of the pointers and updates them accordingly.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.