By Claudine Nicolette. Electrical Wiring. Publised at Monday, January 08th 2018, 22:20:12 PM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Dorian Yannic. Electrical Wiring. Published at Friday, February 16th 2018, 23:39:49 PM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Mailys Laurent. Electrical Wiring. Published at Friday, February 16th 2018, 21:42:01 PM. The ease of loading and unloading the PCBs, as well as the ability to handle multiple PCBs, are important in high production lines. In addition, fixtures should provide thermal protection to the heat sensitive areas of the PCB.
By Adrienne Emmanuel. Electrical Wiring. Published at Thursday, February 15th 2018, 15:47:15 PM. The fixtures are usually available in a variety of designs, materials, sizes, and thicknesses. Some can carry more than one board hence allowing the processing of multiple PCBs simultaneously. Other designs have adjustments to support both the primary and secondary side processes.
By Dorian Yannic. Motor Wiring. Published at Wednesday, February 14th 2018, 23:45:01 PM. Electronic motors are found in kids toys, RC cars, airplanes and helicopters, printers, scanners, and fax machines. They are expensive when purchased, quantity 1, new with manual. This is because the motors are part of a supply chain that is usually just making enough to fill orders for kids toys, etc. Many can be found for sale on the internet, but very few are in stock and the price is high if they are. Often it is easier to purchase the kids toy and take it apart. The goal is to connect these motors to the arduino and then make something new with them. The goal of this document is to describe what to expect.
By Fleurette Nina. Car Wiring. Published at Wednesday, February 14th 2018, 19:26:51 PM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Gaspard Magalie. Car Wiring. Published at Wednesday, February 14th 2018, 13:54:05 PM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Claudine Nicolette. Motor Wiring. Published at Wednesday, February 14th 2018, 13:26:18 PM. This means that when the next electromagnet is turned on and the first is turned off, the gear rotates slightly to align with the next one. From there the process is repeated. Each of those rotations is called a "step", with an integer number of steps making a full rotation. In that way, the motor can be turned by a precise angle.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.