By Olivier Constance. Car Wiring. Publised at Monday, November 27th 2017, 06:22:09 AM. Cars are filled with stuff that can make or break performance. The engine needs to be fed the proper amounts of air, fuel, and spark. The suspension and brakes must be in tip-top shape. The wheels and tires, transmission, cooling system, gauges—even the seats—must all function properly.
By Claudine Nicolette. Electrical Wiring. Published at Monday, January 08th 2018, 22:20:12 PM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Dorian Yannic. Car Wiring. Published at Monday, January 08th 2018, 17:17:00 PM. Wires are usually connected to components by plastic-covered terminals which push on to a blade on the unit called a spade terminal. Nearly all types of terminals should be fitted to the wire with crimping pliers. There are a few types such as the "Scotchlok" which are secured by clips. For additional security, you can add solder to the wire.
By Dorian Yannic. Electrical Wiring. Published at Monday, January 08th 2018, 16:08:43 PM. However, the SMT components and the traces must be at least 3.00 mm from the perforation holes. This prevents the damage to the PCB or components which can occur due to surface stress and splinter when separating the boards. One drawback with this method is that it may leave some unwanted board protrusions on the edges.
By Olivier Constance. Electrical Wiring. Published at Monday, January 08th 2018, 13:07:10 PM. When implementing a real-time system, we find a circular buffer critical whether we are using a DSP processor or a general purpose processor (GPP). However, with a GPP we may have to implement the circular buffer in software. As discussed in the previous section, with each new sample, we have to update the pointer which contains the address of the newest sample. With a circular buffer implemented in software, the programmer needs to take care of updating the buffer pointers after each read and write operation. When the pointer reaches the end of the buffer, the program must wrap the pointer back to the beginning of the buffer.
By Adrienne Emmanuel. Car Wiring. Published at Monday, January 08th 2018, 11:01:23 AM. Wires and bundles of wires are clipped to the bodywork to keep them out of the way. Where they run through a hole, the sharp edges are lined with a rubber grommet. Sometimes the loom is divided into sections joined by multi-pin plugs and sockets, so that it can be removed and refitted section by section.
By Fleurette Nina. Electrical Wiring. Published at Monday, January 08th 2018, 08:44:07 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Dorian Yannic. Electrical Wiring. Published at Monday, January 08th 2018, 04:49:54 AM. In a demanding application, we may not have the time to continuously check the pointers to see if they have reached the end of the buffer and wrap them back to the beginning of the buffer when necessary. As a result, a DSP processor uses dedicated hardware to provide some fast circular buffers.This hardware implementation automatically checks the status of the pointers and updates them accordingly.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.