By Olivier Constance. Car Wiring. Publised at Monday, November 27th 2017, 06:22:09 AM. Brushes are used to create electrical contact to the commutator segments and when current is fed into two of the four brushes, it flows through all the loops of the armature and shoe windings and out the other two brushes. This creates a magnetic field around each loop. As the armature turns, the loop will move to a position where the current flow reverses. This constant reversal of current flow allows the armature and field coils to repel each other and spin the motor. The greater the current flowing in the coils, the greater the magnetic forces, and the greater the power of the motor.
By Fleurette Nina. Car Wiring. Published at Wednesday, February 14th 2018, 19:26:51 PM. Cable sizes are given by two numbers. The first one is the number of strands. The second (which is always the same in car wiring) is the diameter of each strand in millimetres. Twisting wires together and fitting spade terminals twist bare ends together and solder them.Cover the joint with insulating tape. Tag connectors are closedround the bare wire withpliers, then soldered. A spade terminal is easy to disconnect andreconnect. Methods of joining, wires To connect two wires, use a wire stripper to remove about in. (19 mm) of insulation from each wire.
By Gaspard Magalie. Car Wiring. Published at Wednesday, February 14th 2018, 13:54:05 PM. Push a screwdriver blade through the grommet carefully to enlarge it for the new cables, taking care not to damage insulation on existing wires. If you pass a cable through a new hole, fit the hole with a grommet. To pass wires up door pillars or behind trim, tape them to a piece of fairly stiff wire, poke it carefully behind the trim or up the pillar, and pull it through at the far end, bringing the wire with it.
By Claudine Nicolette. Motor Wiring. Published at Wednesday, February 14th 2018, 13:26:18 PM. The two wires of the brushed dc motor can be thought of as forward and reverse. The three wires of brushless can be thought of as 1, 2 and 3. Going forward would be this sequence 1-2, 2-3, 3-1, 1-2, etc. Going backwards would be 1-3, 3-2, 2-1, 1-3, etc. What this means is that one third of the motor is helping maintain momentum while another third is pulling the motor in a new direction.
By Fleurette Nina. Car Wiring. Published at Wednesday, February 14th 2018, 07:06:57 AM. If possible, use an insulated in-line crimp connector. Test each mended wire with a circuit tester and battery, connected to the nearest connectors either side of the mend. Re-wrap the exposed section of the loom with self-adhesive or "clingfilm" PVC insulating tape. Put some layers between the exposed section and adjoining wires - not merely a cover over the top - then fit the loom back into the car. Reconnect all terminals and clips, then test all the electrical components involved.
By Adrienne Emmanuel. Motor Wiring. Published at Wednesday, February 14th 2018, 06:58:56 AM. Brushed DC motors rotate continuously when DC voltage is applied to their terminals. The stepper motor is known by its property to convert a train of input pulses (typically square wave pulses) into a precisely defined increment in the shaft position. Each pulse moves the shaft through a fixed angle. Stepper motors effectively have multiple "toothed" electromagnets arranged around a central gear-shaped piece of iron. The electromagnets are energized by an external driver circuit or a micro controller. To make the motor shaft turn, first, one electromagnet is given power, which magnetically attracts the gear teeth. When the gear teeth are aligned to the first electromagnet, they are slightly offset from the next electromagnet.
By Adrienne Emmanuel. Car Wiring. Published at Tuesday, February 13th 2018, 20:19:44 PM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Mailys Laurent. Car Wiring. Published at Tuesday, February 13th 2018, 18:46:51 PM. But it is better to replace the terminal once corrosion has destroyed the surface coating. Making repairs to the loom Use a circuit tester to check if single wires are damaged. The wiring loom itself seldom goes wrong, but after other repairs have been made, a cable may be trapped and its insulation cut through, causing a short circuit.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.