By Olivier Constance. Car Wiring. Publised at Monday, November 27th 2017, 06:22:09 AM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Dorian Yannic. Electrical Wiring. Published at Saturday, November 11th 2017, 11:56:59 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Dorian Yannic. Motor Wiring. Published at Friday, November 10th 2017, 03:07:38 AM. 3 wires. Brushless motors are more expensive than dc brushed motors. Lots of PC fans are brushless motors. The motor that drives the paper path in laser printers is brushless. They are build differently than servo or brushed motors. There are no places where metal is rubbing against metal. Brushless motors will last longer, spin faster, help batteries last longer. They have three wires instead of two. There are two types: inrunner and outrunner.
By France Barbara. Electrical Wiring. Published at Tuesday, November 07th 2017, 00:10:46 AM. The ease of loading and unloading the PCBs, as well as the ability to handle multiple PCBs, are important in high production lines. In addition, fixtures should provide thermal protection to the heat sensitive areas of the PCB.
By Gaspard Magalie. Motor Wiring. Published at Monday, November 06th 2017, 04:29:01 AM. 2 wires. Servomechanisms are designed to move to a spot and hold it is position. They are not designed to spin continuously. Used to position print heads in ink jet printers, plotters, scanners. Travel at set speeds. Go to a spot and stop. When stopped and still turned on, will attempt to hold it is position. Forcing it to move in this position can damage the motor. Typically is controlled by a circuit board that counts shadows with an LED and light sensor or has a resistor that changes value depending upon position. Often zooms to one side when powered on to figure out where it is at.
By Olivier Constance. Electrical Wiring. Published at Thursday, November 02nd 2017, 20:16:28 PM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 31st 2017, 22:07:54 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Fleurette Nina. Motor Wiring. Published at Monday, October 30th 2017, 15:14:10 PM. Brushed DC motors rotate continuously when DC voltage is applied to their terminals. The stepper motor is known by its property to convert a train of input pulses (typically square wave pulses) into a precisely defined increment in the shaft position. Each pulse moves the shaft through a fixed angle. Stepper motors effectively have multiple "toothed" electromagnets arranged around a central gear-shaped piece of iron. The electromagnets are energized by an external driver circuit or a micro controller. To make the motor shaft turn, first, one electromagnet is given power, which magnetically attracts the gear teeth. When the gear teeth are aligned to the first electromagnet, they are slightly offset from the next electromagnet.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.