By Olivier Constance. Car Wiring. Publised at Monday, November 27th 2017, 06:22:09 AM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Adrienne Emmanuel. Electrical Wiring. Published at Wednesday, January 10th 2018, 09:27:23 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Claudine Nicolette. Electrical Wiring. Published at Wednesday, January 10th 2018, 05:08:28 AM. The tab-route or breakaway tab method is suitable for PCBs with either similar or different designs, or where it is not possible or practical to use the V-grooves. The designer leaves a perforated tabs routing space between the different or similar boards, hence allowing for separation after processing.
By Fleurette Nina. Car Wiring. Published at Tuesday, January 09th 2018, 21:34:30 PM. Use insulating tape in a spiral to bind wires together. If you have to lead a new wire along a difficult route - to the rear of the car, for example - you could take the opportunity to lead a spare wire at the same time, for any accessory you might want to fit later. Cover the end of a spare wire with insulating tape to prevent an electrical short circuit. Identifying cable sizes 14/30 cable 65/30 cable High-tension (HT) lead The starter cable Types of cable.
By Olivier Constance. Motor Wiring. Published at Tuesday, January 09th 2018, 20:50:54 PM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
By Dorian Yannic. Car Wiring. Published at Tuesday, January 09th 2018, 19:40:09 PM. It is commonly known as the BENDIX type of solenoid. Such solenoids operate in three stages, the disengaged, partially engaged and engaged. In the disengaged position the drive gear is released and no current is flowing. In the partially engaged stage, current from the starter switch flows through both the pull-in and the hold-in coils.
By Cyrille Lothaire. Car Wiring. Published at Tuesday, January 09th 2018, 19:31:59 PM. Wires are usually connected to components by plastic-covered terminals which push on to a blade on the unit called a spade terminal. Nearly all types of terminals should be fitted to the wire with crimping pliers. There are a few types such as the "Scotchlok" which are secured by clips. For additional security, you can add solder to the wire.
By Cyrille Lothaire. Car Wiring. Published at Tuesday, January 09th 2018, 14:11:38 PM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.