By Olivier Constance. Car Wiring. Publised at Monday, November 27th 2017, 06:22:09 AM. The damage caused by overheated wires is easy to find; but if only a single wire has overheated and melted at some point, you may have to use a circuit tester to find the break. If the damage is in an open run of wiring, you may be able to mend separate wires without taking out a section of the loom. If it is in any part of the covered sections, you need to remove at least part of the wiring loom.
By Claudine Nicolette. Car Wiring. Published at Friday, December 29th 2017, 01:22:14 AM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Dorian Yannic. Car Wiring. Published at Friday, December 29th 2017, 00:08:27 AM. Wires are usually connected to components by plastic-covered terminals which push on to a blade on the unit called a spade terminal. Nearly all types of terminals should be fitted to the wire with crimping pliers. There are a few types such as the "Scotchlok" which are secured by clips. For additional security, you can add solder to the wire.
By Adrienne Emmanuel. Electrical Wiring. Published at Thursday, December 28th 2017, 21:36:39 PM. The fixture should support the board and prevent distortion as the board goes through the printing, component placement, and reflow processes. Its construction should ensure adequate protection for the bottom side components during the double-sided reflow process.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 21:29:40 PM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 21:14:12 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Olivier Constance. Motor Wiring. Published at Thursday, December 28th 2017, 20:07:50 PM. The arduino sends pulses to the servo motor much like sending them to an ESC. The pulses have a different meaning. The pulses describe a spot to go to. Within the servo there is a feedback mechanism that counts shadows or turns a variable resistor. The servo circuit board then moves the servo to that spot. It knows when it has reached the spot when a certain number of shadows have past or when the resistance reaches a certain value. The arduino has to keep sending the same position over and over again to hold the motor in a current spot. Short pulses go one direction, long pulses the opposite direction, medium pulse widths go to the middle. Middle is typically 1.5 milli seconds.
By Claudine Nicolette. Car Wiring. Published at Thursday, December 28th 2017, 19:22:21 PM. If an outlying part of the loom with few wires has been damaged, it may be simpler to replace each wire to the end of the loom instead of inserting a section. If so, use the old, damaged wire as a guide to the length of the new. In an open area of wiring, join old and new with snap connectors.Fitting new wiring Fit a rubber grommet when passing wires through a new hole in the bodywork. When you fit accessories you must use large enough cables. As far as you can, route the new wiring along the course of the existing loom, using the same clips and grommets.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.