By Dorian Yannic. Electrical Wiring. Publised at Saturday, September 30th 2017, 19:13:18 PM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 21:14:12 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Olivier Constance. Motor Wiring. Published at Thursday, December 28th 2017, 20:07:50 PM. Parts of the motor are often attached to a circuit board. Magnets are attached on the inside of the can that spins with the shaft .. sort of like a spinning umbrella. All brushless motors have a spinning umbrella. Inside the umbrella is a permanent magnet. It looks like one continuous round magnet. However it is more like series of magnets.
By Claudine Nicolette. Car Wiring. Published at Thursday, December 28th 2017, 19:22:21 PM. Brushes are used to create electrical contact to the commutator segments and when current is fed into two of the four brushes, it flows through all the loops of the armature and shoe windings and out the other two brushes. This creates a magnetic field around each loop. As the armature turns, the loop will move to a position where the current flow reverses. This constant reversal of current flow allows the armature and field coils to repel each other and spin the motor. The greater the current flowing in the coils, the greater the magnetic forces, and the greater the power of the motor.
By Gaspard Magalie. Electrical Wiring. Published at Thursday, December 28th 2017, 17:50:11 PM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Dorian Yannic. Car Wiring. Published at Thursday, December 28th 2017, 17:40:13 PM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 17:11:16 PM. This IC is available only in an 8-pin dual-flat no-leads (DFN) package, measuring a scant 2.5mm × 2.5mm with a tiny thickness of only 0.9mm. There is also, in addition to the eight pins, a thermal pad that is connected to ground (see image below).
By Mailys Laurent. Car Wiring. Published at Thursday, December 28th 2017, 17:09:32 PM. If possible, use an insulated in-line crimp connector. Test each mended wire with a circuit tester and battery, connected to the nearest connectors either side of the mend. Re-wrap the exposed section of the loom with self-adhesive or "clingfilm" PVC insulating tape. Put some layers between the exposed section and adjoining wires - not merely a cover over the top - then fit the loom back into the car. Reconnect all terminals and clips, then test all the electrical components involved.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.