By Olivier Constance. Car Wiring. Publised at Monday, January 22nd 2018, 10:14:47 AM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Fleurette Nina. Electrical Wiring. Published at Thursday, October 12th 2017, 05:54:44 AM. However, the SMT components and the traces must be at least 3.00 mm from the perforation holes. This prevents the damage to the PCB or components which can occur due to surface stress and splinter when separating the boards. One drawback with this method is that it may leave some unwanted board protrusions on the edges.
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 10th 2017, 02:36:22 AM. digital signal processor is a specialized microprocessor for the kind of algorithms employed in digital signal processing (DSP). The main goal is to accelerate the calculations while keeping the power consumption as low as possible. In this article, we review a basic addressing capability of DSP processors, i.e. circular buffering, which allows us to significantly accelerate the data transfer in a real-time system. Please note that since the acronym “DSP” stands for both “digital signal processing” and “digital signal processor," we will use the term “DSP processor” when referring to the hardware rather than the algorithm.
By Claudine Nicolette. Motor Wiring. Published at Saturday, October 07th 2017, 00:23:28 AM. The motor can be directly pulsed by the arduino. The arduino can also supply power to the motor, but normally this is only a good idea for demonstration purposes. The arduino has a very weak power supply, and attempting to power a motor through it can destroy the arduino. Furthermore, the arduino may not be able to supply the exact correct maximum voltage. For this reason, an ESC is placed between the arduino and the motor.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, October 04th 2017, 00:20:15 AM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Mailys Laurent. Electrical Wiring. Published at Monday, October 02nd 2017, 21:00:02 PM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, October 01st 2017, 20:21:48 PM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Dorian Yannic. Electrical Wiring. Published at Saturday, September 30th 2017, 19:13:18 PM. There are different panelization and de-panelization methods depending on the application of the PCB, thickness, shape, component layout, type of edges, and other factors. The two popular methods are the V-groove panelization and the breakaway tab panelization. Each of these uses a different method to separate the boards from the main array and has its advantages and limitations.
Recent post
Category
Monthly Archives
Static Page
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.