By Cyrille Lothaire. Car Wiring. Publised at Saturday, January 06th 2018, 06:48:56 AM. Cut out all the damaged wires with wire cutters. Spread out the cuts across a bundle of several wires: if many joins are opposite each other their bulk may make it difficult to fit the loom into the car. If possible, replace wiring with new wire of the same colour. The new wire must be the right size: there are five sizes, depending on current rating. Repairs in wrapped sections of the loom are the only places where you may join wires by twisting them together and soldering the joint mainly because there may not be room for any other method.
By France Barbara. Electrical Wiring. Published at Sunday, February 11th 2018, 00:47:29 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Mailys Laurent. Car Wiring. Published at Saturday, February 10th 2018, 22:21:26 PM. With all those things to worry about, many enthusiasts overlook the electrical wiring system. A lousy wiring job will keep your electrical accessories from operating at full potential—and that means subpar performance. Many people are intimidated by the prospect of wiring a vehicle. But a proper wiring job doesn’t have to be a scary task—we’ve put together a few tips to help make the job a little bit smoother.
By Gaspard Magalie. Electrical Wiring. Published at Friday, February 09th 2018, 18:55:23 PM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By France Barbara. Motor Wiring. Published at Friday, February 09th 2018, 10:50:14 AM. Electronic motors are found in kids toys, RC cars, airplanes and helicopters, printers, scanners, and fax machines. They are expensive when purchased, quantity 1, new with manual. This is because the motors are part of a supply chain that is usually just making enough to fill orders for kids toys, etc. Many can be found for sale on the internet, but very few are in stock and the price is high if they are. Often it is easier to purchase the kids toy and take it apart. The goal is to connect these motors to the arduino and then make something new with them. The goal of this document is to describe what to expect.
By Cyrille Lothaire. Motor Wiring. Published at Friday, January 26th 2018, 19:25:31 PM. Outrunners and inrunners both use the same ESC. This ESC is different than that of the brushed DC motor. There are three wires going to the motor instead of two. The wiring between the ESC and the Arduino consists if the same 5 wires. The three wires give the brushless motors more pulling power. Understanding this helps understand stepper motors below.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, January 24th 2018, 21:46:51 PM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Olivier Constance. Car Wiring. Published at Monday, January 22nd 2018, 10:14:47 AM. The damage caused by overheated wires is easy to find; but if only a single wire has overheated and melted at some point, you may have to use a circuit tester to find the break. If the damage is in an open run of wiring, you may be able to mend separate wires without taking out a section of the loom. If it is in any part of the covered sections, you need to remove at least part of the wiring loom.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.