By Mailys Laurent. Car Wiring. Publised at Thursday, December 28th 2017, 17:09:32 PM. But it is better to replace the terminal once corrosion has destroyed the surface coating. Making repairs to the loom Use a circuit tester to check if single wires are damaged. The wiring loom itself seldom goes wrong, but after other repairs have been made, a cable may be trapped and its insulation cut through, causing a short circuit.
By Fleurette Nina. Electrical Wiring. Published at Sunday, December 31st 2017, 02:18:44 AM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Olivier Constance. Car Wiring. Published at Sunday, December 31st 2017, 00:36:48 AM. Push a screwdriver blade through the grommet carefully to enlarge it for the new cables, taking care not to damage insulation on existing wires. If you pass a cable through a new hole, fit the hole with a grommet. To pass wires up door pillars or behind trim, tape them to a piece of fairly stiff wire, poke it carefully behind the trim or up the pillar, and pull it through at the far end, bringing the wire with it.
By Fleurette Nina. Motor Wiring. Published at Saturday, December 30th 2017, 23:49:44 PM. Identical model motors vary, so each needs to be calibrated by banging against some edge ... think of the banging noise when an inkjet printer is turned on. Servo motors are good for robot wheels that have to turn a certain distance then stop. They are good for robots that have to balance themselves somehow. Auto pilots can use these to navigate a hallway. They are not good for spinning propellers like brushed dc motors and brushless motors.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, December 30th 2017, 22:36:59 PM. Brushless outrunners are always built on a circuit board. This makes them cheaper. The circuit board for this CD motor has no electronics on it. A ribbon cable attaches 11 wires to another controller circuit board. But often the controller is built onto the same circuit board. The circuit boards interface with a controller in two ways.
By Gaspard Magalie. Electrical Wiring. Published at Saturday, December 30th 2017, 21:46:15 PM. You can see how all the power supply connections use large traces or copper pours. The AWG doesn’t have high current requirements, but the board house doesn’t give you a discount for using less copper, so you might as well opt for large (= low-resistance, low-inductance) traces if you have the room.
By Mailys Laurent. Electrical Wiring. Published at Saturday, December 30th 2017, 21:23:01 PM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 19:12:00 PM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.