By Mailys Laurent. Car Wiring. Publised at Thursday, December 28th 2017, 17:09:32 PM. Use insulating tape in a spiral to bind wires together. If you have to lead a new wire along a difficult route - to the rear of the car, for example - you could take the opportunity to lead a spare wire at the same time, for any accessory you might want to fit later. Cover the end of a spare wire with insulating tape to prevent an electrical short circuit. Identifying cable sizes 14/30 cable 65/30 cable High-tension (HT) lead The starter cable Types of cable.
By Adrienne Emmanuel. Car Wiring. Published at Wednesday, September 27th 2017, 18:52:26 PM. If this does not blow a fuse the wiring overheats and melts insulation, perhaps starting a fire. A similar result can come from fitting accessories incorrectly, or if power demand is too high for the size of the wire being used. After many years, insulation may become hard and brittle, particularly where it is exposed to heat, as in the engine bay. Sections, or all of the loom, may need replacing.
By Gaspard Magalie. Electrical Wiring. Published at Tuesday, September 26th 2017, 17:22:48 PM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 24th 2017, 00:10:58 AM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By Adrienne Emmanuel. Motor Wiring. Published at Saturday, September 23rd 2017, 20:20:29 PM. RC servos are used to provide actuation for various mechanical systems such as the steering of a car, the control surfaces on a plane, or the rudder of a boat. Due to their affordability, reliability, and simplicity of control by microprocessors, they are often used in small-scale robotics applications. A standard RC receiver (or a microcontroller) sends pulse-width modulation (PWM) signals to the servo. The electronics inside the servo translate the width of the pulse into a position. When the servo is commanded to rotate, the motor is powered until the potentiometer reaches the value corresponding to the commanded position.
By Fleurette Nina. Motor Wiring. Published at Thursday, September 21st 2017, 18:43:05 PM. Bipolar motors have a single winding per phase. The current in a winding needs to be reversed in order to reverse a magnetic pole, so the driving circuit must be more complicated, typically with an H-bridge arrangement "however there are several off-the-shelf driver chips available to make this a simple affair". There are two leads per phase, none are common.Static friction effects using an H-bridge have been observed with certain drive topologies.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 17th 2017, 03:23:46 AM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By France Barbara. Electrical Wiring. Published at Saturday, September 16th 2017, 00:10:12 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.