By Gaspard Magalie. Electrical Wiring. Publised at Friday, February 09th 2018, 18:55:23 PM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By Cyrille Lothaire. Car Wiring. Publised at Friday, January 05th 2018, 19:31:18 PM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Gaspard Magalie. Motor Wiring. Published at Thursday, December 28th 2017, 10:08:52 AM. Speed can be varied by either changing the voltage or pulsing the motor. Most computer controlled DC motors are pulsed. Pulses of a fixed voltage are sent to the motor, usually by an Electronic Speed Controller or ESC. A pulse of 1.5 ms causes no motion. Wider pulses cause faster spinning in one direction. Shorter pulses cause faster spinning in the opposite direction. Eventually, an overstressed ESC stops pulsing and turns one wire on and one wire off, depending on the direction.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 07:48:26 AM. Care should be taken when depaneling the perforated-tab PCB array; otherwise, an incorrect method will splinter or tear the solder-mask or active surface layer. The ideal breakout method should not cause any damage to the board or transfer stress from the PCB surface to the components.
By Fleurette Nina. Motor Wiring. Published at Thursday, December 28th 2017, 05:54:53 AM. Identical model motors vary, so each needs to be calibrated by banging against some edge ... think of the banging noise when an inkjet printer is turned on. Servo motors are good for robot wheels that have to turn a certain distance then stop. They are good for robots that have to balance themselves somehow. Auto pilots can use these to navigate a hallway. They are not good for spinning propellers like brushed dc motors and brushless motors.
By Fleurette Nina. Electrical Wiring. Published at Thursday, December 28th 2017, 05:52:53 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Mailys Laurent. Electrical Wiring. Published at Thursday, December 28th 2017, 05:20:31 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Cyrille Lothaire. Electrical Wiring. Published at Thursday, December 28th 2017, 05:00:05 AM. The ease of loading and unloading the PCBs, as well as the ability to handle multiple PCBs, are important in high production lines. In addition, fixtures should provide thermal protection to the heat sensitive areas of the PCB.
By Adrienne Emmanuel. Car Wiring. Published at Thursday, December 28th 2017, 03:09:28 AM. The driven "or friction" plate runs on a splined input shaft, through which the power is transmitted to the gearbox. The plate has friction linings, similar to brake linings, on both its faces. This allows the drive to be taken up smoothly when the clutch is engaged. When the clutch is disengaged "pedal depressed", an arm pushes a release bearing against the centre of the diaphragm spring which releases the clamping pressure. The outer part of the pressure plate, which has a large friction surface, then no longer clamps the driven plate to the flywheel, so the transmission of power is interrupted and gears can be changed.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.