By Olivier Constance. Car Wiring. Publised at Thursday, January 04th 2018, 06:05:59 AM. Cars are filled with stuff that can make or break performance. The engine needs to be fed the proper amounts of air, fuel, and spark. The suspension and brakes must be in tip-top shape. The wheels and tires, transmission, cooling system, gauges—even the seats—must all function properly.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 17th 2017, 03:23:46 AM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By France Barbara. Electrical Wiring. Published at Saturday, September 16th 2017, 00:10:12 AM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Mailys Laurent. Motor Wiring. Published at Thursday, September 14th 2017, 20:19:13 PM. The five wires coming off the circuit board are the same as those coming off the ESC attached to the brushed dc motor and the servo motor circuit board "2 for power in and 3 go to the arduino". The pulses mean the same as the brushless dc motor. The only difference is that at maximum RPM, there are still pulses. There is not one long pulse like the brushed dc motor. The only physical difference is that there are three wires into the motor you may not be able to see them when it is mounted on a circuit board.
By Gaspard Magalie. Motor Wiring. Published at Monday, September 11th 2017, 19:50:47 PM. Brushed DC motors rotate continuously when DC voltage is applied to their terminals. The stepper motor is known by its property to convert a train of input pulses (typically square wave pulses) into a precisely defined increment in the shaft position. Each pulse moves the shaft through a fixed angle. Stepper motors effectively have multiple "toothed" electromagnets arranged around a central gear-shaped piece of iron. The electromagnets are energized by an external driver circuit or a micro controller. To make the motor shaft turn, first, one electromagnet is given power, which magnetically attracts the gear teeth. When the gear teeth are aligned to the first electromagnet, they are slightly offset from the next electromagnet.
By Fleurette Nina. Motor Wiring. Published at Sunday, September 10th 2017, 11:18:59 AM. Servo motors are usually mounted on a circuit board. Some have two wires traveling to the circuit board much like between a DC motor and ESC. Attached to the board are wires for motor power and again three wires going to the arduino, the same three wires mentioned above.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, September 09th 2017, 08:13:56 AM. Parts of the motor are often attached to a circuit board. Magnets are attached on the inside of the can that spins with the shaft .. sort of like a spinning umbrella. All brushless motors have a spinning umbrella. Inside the umbrella is a permanent magnet. It looks like one continuous round magnet. However it is more like series of magnets.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, September 06th 2017, 04:45:11 AM. This IC is available only in an 8-pin dual-flat no-leads (DFN) package, measuring a scant 2.5mm × 2.5mm with a tiny thickness of only 0.9mm. There is also, in addition to the eight pins, a thermal pad that is connected to ground (see image below).
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.