By Fleurette Nina. Car Wiring. Publised at Tuesday, January 09th 2018, 09:25:53 AM. Use insulating tape in a spiral to bind wires together. If you have to lead a new wire along a difficult route - to the rear of the car, for example - you could take the opportunity to lead a spare wire at the same time, for any accessory you might want to fit later. Cover the end of a spare wire with insulating tape to prevent an electrical short circuit. Identifying cable sizes 14/30 cable 65/30 cable High-tension (HT) lead The starter cable Types of cable.
By Cyrille Lothaire. Car Wiring. Published at Saturday, December 30th 2017, 02:17:52 AM. Even if only one wire has overheated, inspect all the others to make sure their insulation is not damaged. Before cutting out damaged wires, make sure that the colour coding is the same at each end of the damaged section of each wire, and that it is not so discoloured that it is unrecognisable. If there is any chance of confusion, label both ends.
By Gaspard Magalie. Electrical Wiring. Published at Friday, December 29th 2017, 23:04:12 PM. The decoupling capacitors (C4, C5, C6, C7, C9, C10, C11) are arranged around the perimeter of the chip, very close to their respective power pins and to the vias that connect the caps to the internal planes. Notice how the smaller cap is always closer to the power pin; this is because we rely more on the lower-value capacitor for high-frequency bypassing, and thus the first priority is minimizing the inductance and resistance between the smaller cap and the pin.
By Claudine Nicolette. Electrical Wiring. Published at Friday, December 29th 2017, 20:19:29 PM. The ease of loading and unloading the PCBs, as well as the ability to handle multiple PCBs, are important in high production lines. In addition, fixtures should provide thermal protection to the heat sensitive areas of the PCB.
By Adrienne Emmanuel. Electrical Wiring. Published at Friday, December 29th 2017, 20:12:23 PM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By Dorian Yannic. Electrical Wiring. Published at Friday, December 29th 2017, 15:30:43 PM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Mailys Laurent. Electrical Wiring. Published at Friday, December 29th 2017, 09:43:55 AM. The fixture should support the board and prevent distortion as the board goes through the printing, component placement, and reflow processes. Its construction should ensure adequate protection for the bottom side components during the double-sided reflow process.
By Fleurette Nina. Motor Wiring. Published at Friday, December 29th 2017, 08:52:17 AM. Positioning servomechanisms were first used in military fire-control and marine navigation equipment. Today servomechanisms are used in automatic machine tools, satellite-tracking antennas, remote control airplanes, automatic navigation systems on boats and planes, and antiaircraft-gun control systems. Other examples are fly-by-wire systems in aircraft which use servos to actuate the aircraft control surfaces, and radio-controlled models which use RC servos for the same purpose. Many autofocus cameras also use a servomechanism to accurately move the lens. A hard disk drive has a magnetic servo system with sub-micrometre positioning accuracy. In industrial machines, servos are used to perform complex motion, in many applications.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.