By Olivier Constance. Electrical Wiring. Publised at Friday, January 12th 2018, 09:10:55 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Olivier Constance. Car Wiring. Published at Saturday, December 30th 2017, 08:37:15 AM. If an outlying part of the loom with few wires has been damaged, it may be simpler to replace each wire to the end of the loom instead of inserting a section. If so, use the old, damaged wire as a guide to the length of the new. In an open area of wiring, join old and new with snap connectors.Fitting new wiring Fit a rubber grommet when passing wires through a new hole in the bodywork. When you fit accessories you must use large enough cables. As far as you can, route the new wiring along the course of the existing loom, using the same clips and grommets.
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 08:31:27 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Dorian Yannic. Car Wiring. Published at Saturday, December 30th 2017, 06:55:37 AM. Wires are usually connected to components by plastic-covered terminals which push on to a blade on the unit called a spade terminal. Nearly all types of terminals should be fitted to the wire with crimping pliers. There are a few types such as the "Scotchlok" which are secured by clips. For additional security, you can add solder to the wire.
By Gaspard Magalie. Motor Wiring. Published at Saturday, December 30th 2017, 05:48:48 AM. Stepper motor performance is strongly dependent on the driver circuit. Torque curves may be extended to greater speeds if the stator poles can be reversed more quickly, the limiting factor being a combination of the winding inductance. To overcome the inductance and switch the windings quickly, one must increase the drive voltage. This leads further to the necessity of limiting the current that these high voltages may otherwise induce.
By Gaspard Magalie. Car Wiring. Published at Saturday, December 30th 2017, 04:07:17 AM. Cable sizes are given by two numbers. The first one is the number of strands. The second (which is always the same in car wiring) is the diameter of each strand in millimetres. Twisting wires together and fitting spade terminals twist bare ends together and solder them.Cover the joint with insulating tape. Tag connectors are closedround the bare wire withpliers, then soldered. A spade terminal is easy to disconnect andreconnect. Methods of joining, wires To connect two wires, use a wire stripper to remove about in. (19 mm) of insulation from each wire.
By Cyrille Lothaire. Car Wiring. Published at Saturday, December 30th 2017, 02:17:52 AM. Rubber grommets are used where wirespass through holes drilled in the bodywork,to prevent sharp edges cutting theinsulation. Cable clips The loom and individual cables areheld to the bodywork by various types of clips.
By Gaspard Magalie. Electrical Wiring. Published at Friday, December 29th 2017, 23:04:12 PM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.