By Dorian Yannic. Electrical Wiring. Publised at Saturday, September 30th 2017, 19:13:18 PM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By Adrienne Emmanuel. Electrical Wiring. Published at Sunday, January 07th 2018, 00:09:05 AM. The tab-route or breakaway tab method is suitable for PCBs with either similar or different designs, or where it is not possible or practical to use the V-grooves. The designer leaves a perforated tabs routing space between the different or similar boards, hence allowing for separation after processing.
By Adrienne Emmanuel. Motor Wiring. Published at Saturday, January 06th 2018, 18:23:53 PM. An additional limitation, often comparable to the effects of inductance, is the back-EMF of the motor. As the motor rotor turns, a sinusoidal voltage is generated proportional to the speed (step rate). This AC voltage is subtracted from the voltage waveform available to induce a change in the current.
By Fleurette Nina. Electrical Wiring. Published at Saturday, January 06th 2018, 16:05:56 PM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Adrienne Emmanuel. Car Wiring. Published at Saturday, January 06th 2018, 14:35:53 PM. Twist the bare ends together, then use pliers to press the twisted section into a compact shape. Solder the wires together so that they cannot be pulled apart, using only a little solder to avoid making the joint bulky. Wind insulating tape in a spiral over the joint.
By Fleurette Nina. Car Wiring. Published at Saturday, January 06th 2018, 13:05:48 PM. Brushes are used to create electrical contact to the commutator segments and when current is fed into two of the four brushes, it flows through all the loops of the armature and shoe windings and out the other two brushes. This creates a magnetic field around each loop. As the armature turns, the loop will move to a position where the current flow reverses. This constant reversal of current flow allows the armature and field coils to repel each other and spin the motor. The greater the current flowing in the coils, the greater the magnetic forces, and the greater the power of the motor.
By Fleurette Nina. Electrical Wiring. Published at Saturday, January 06th 2018, 11:44:36 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, January 06th 2018, 11:02:35 AM. Speed can be varied by either changing the voltage or pulsing the motor. Most computer controlled DC motors are pulsed. Pulses of a fixed voltage are sent to the motor, usually by an Electronic Speed Controller or ESC. A pulse of 1.5 ms causes no motion. Wider pulses cause faster spinning in one direction. Shorter pulses cause faster spinning in the opposite direction. Eventually, an overstressed ESC stops pulsing and turns one wire on and one wire off, depending on the direction.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.