By Olivier Constance. Car Wiring. Publised at Friday, August 04th 2017, 00:40:38 AM. STARTER SOLENOID "Relay" — All cars are wired so that the batterys main cable connects to the starter motor windings "the thick cable is needed for large current flow, right?". This wire must be switched on and off, of course, and it would be costly and inefficient to route it through the ignition switch "not to mention the size of the switchs components required to carry such current!". Consequently, a relay is necessary.
By Olivier Constance. Car Wiring. Published at Monday, November 27th 2017, 06:22:09 AM. If an outlying part of the loom with few wires has been damaged, it may be simpler to replace each wire to the end of the loom instead of inserting a section. If so, use the old, damaged wire as a guide to the length of the new. In an open area of wiring, join old and new with snap connectors.Fitting new wiring Fit a rubber grommet when passing wires through a new hole in the bodywork. When you fit accessories you must use large enough cables. As far as you can, route the new wiring along the course of the existing loom, using the same clips and grommets.
By Cyrille Lothaire. Motor Wiring. Published at Thursday, November 23rd 2017, 17:35:26 PM. Stepper motor performance is strongly dependent on the driver circuit. Torque curves may be extended to greater speeds if the stator poles can be reversed more quickly, the limiting factor being a combination of the winding inductance. To overcome the inductance and switch the windings quickly, one must increase the drive voltage. This leads further to the necessity of limiting the current that these high voltages may otherwise induce.
By Dorian Yannic. Electrical Wiring. Published at Wednesday, November 22nd 2017, 13:04:57 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Adrienne Emmanuel. Car Wiring. Published at Friday, November 17th 2017, 02:23:17 AM. Cars are filled with stuff that can make or break performance. The engine needs to be fed the proper amounts of air, fuel, and spark. The suspension and brakes must be in tip-top shape. The wheels and tires, transmission, cooling system, gauges—even the seats—must all function properly.
By Dorian Yannic. Car Wiring. Published at Wednesday, November 15th 2017, 07:22:30 AM. It transmits engine power to the gearbox, and allows transmission to be interrupted while a gear is selected to move off from a stationary position, or when gears are changed while the car is moving. Master cylinder Operatinglinkage Slave cylinder Flywheel The mastercylinder pumpshydraulic fluidin direction ofthe arrow. Most cars use a friction clutch operated either by fluid (hydraulic) or, more commonly, by a cable. When a car is moving under power, the clutch is engaged. A pressure plate bolted to the flywheel exerts constant force, by means of a diaphragm spring, on the driven plate. Earlier cars have a series of coil springs at the back of the pressure plate, instead of a diaphragm spring.
By France Barbara. Electrical Wiring. Published at Sunday, November 12th 2017, 22:18:25 PM. Although this device uses an I2C interface with communication speeds up to 1 MHz, two of the eight pins are dedicated to Alert (pin3) and nReset (pin 6). The Alert pin is intended to be connected, if desired, to an interrupt pin on a microcontroller. According to section 3.5 (ALERT Pin) of the datasheet, "The output of the pin depends on the value of the temperature reading relative to programmable limits," and its function is "explained in a separate application note.
By Dorian Yannic. Electrical Wiring. Published at Saturday, November 11th 2017, 11:56:59 AM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.