By Olivier Constance. Car Wiring. Publised at Friday, August 04th 2017, 00:40:38 AM. Relays are devices that utilize a central iron core fitted closely to the inside of a coil of wire. When the wire is energized the iron core will be drawn down the length of the coil, the direction dependent upon the direction of current flow. If the relays iron core is fitted with large, high current-carrying contacts it can be used as a high-current switch. Relays are used throughout cars for horns, electric fans, air conditioning clutches, etc. and the most important one is the starter solenoid.
By Fleurette Nina. Car Wiring. Published at Thursday, January 04th 2018, 09:31:46 AM. Push the wire into the connector so that the strands just protrude from the round end. Grip the cable, connector uppermost, in a vice or self-locking pliers, so that the connector rests on top of the vice and cannot slide down the wire when soldering. Inside a bullet connector. Apply solder on the top of the connector, and let it melt and run down inside. Trim off the protruding strands with wire cutters.
By Fleurette Nina. Electrical Wiring. Published at Thursday, January 04th 2018, 06:09:42 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Olivier Constance. Car Wiring. Published at Thursday, January 04th 2018, 06:05:59 AM. Cut out all the damaged wires with wire cutters. Spread out the cuts across a bundle of several wires: if many joins are opposite each other their bulk may make it difficult to fit the loom into the car. If possible, replace wiring with new wire of the same colour. The new wire must be the right size: there are five sizes, depending on current rating. Repairs in wrapped sections of the loom are the only places where you may join wires by twisting them together and soldering the joint mainly because there may not be room for any other method.
By Mailys Laurent. Electrical Wiring. Published at Thursday, January 04th 2018, 05:54:37 AM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Olivier Constance. Electrical Wiring. Published at Thursday, January 04th 2018, 04:04:27 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Fleurette Nina. Car Wiring. Published at Thursday, January 04th 2018, 01:54:35 AM. Use insulating tape in a spiral to bind wires together. If you have to lead a new wire along a difficult route - to the rear of the car, for example - you could take the opportunity to lead a spare wire at the same time, for any accessory you might want to fit later. Cover the end of a spare wire with insulating tape to prevent an electrical short circuit. Identifying cable sizes 14/30 cable 65/30 cable High-tension (HT) lead The starter cable Types of cable.
By Dorian Yannic. Car Wiring. Published at Thursday, January 04th 2018, 01:24:43 AM. Wires and bundles of wires are clipped to the bodywork to keep them out of the way. Where they run through a hole, the sharp edges are lined with a rubber grommet. Sometimes the loom is divided into sections joined by multi-pin plugs and sockets, so that it can be removed and refitted section by section.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.