By Dorian Yannic. Motor Wiring. Publised at Friday, November 10th 2017, 03:07:38 AM. A micro controller or stepper motor controller can be used to activate the drive transistors in the right order, and this ease of operation makes unipolar motors popular with hobbyists; they are probably the cheapest way to get precise angular movements. For the experimenter, the windings can be identified by touching the terminal wires together in PM motors. If the terminals of a coil are connected, the shaft becomes harder to turn.
By Claudine Nicolette. Electrical Wiring. Published at Thursday, December 28th 2017, 11:33:40 AM. The fixtures are usually available in a variety of designs, materials, sizes, and thicknesses. Some can carry more than one board hence allowing the processing of multiple PCBs simultaneously. Other designs have adjustments to support both the primary and secondary side processes.
By Fleurette Nina. Car Wiring. Published at Thursday, December 28th 2017, 11:30:31 AM. Wires and bundles of wires are clipped to the bodywork to keep them out of the way. Where they run through a hole, the sharp edges are lined with a rubber grommet. Sometimes the loom is divided into sections joined by multi-pin plugs and sockets, so that it can be removed and refitted section by section.
By Cyrille Lothaire. Electrical Wiring. Published at Thursday, December 28th 2017, 10:45:09 AM. SMT fixtures are rigid PCB carriers that allow manufacturers to load single or multiple irregular boards, and then take them through the standard processing machines. This makes it possible to carry out tasks such as automatic mounting of electronic components, infra-red reflow soldering, wave soldering, automatic testing, etc.
By Olivier Constance. Car Wiring. Published at Thursday, December 28th 2017, 10:09:08 AM. Push a screwdriver blade through the grommet carefully to enlarge it for the new cables, taking care not to damage insulation on existing wires. If you pass a cable through a new hole, fit the hole with a grommet. To pass wires up door pillars or behind trim, tape them to a piece of fairly stiff wire, poke it carefully behind the trim or up the pillar, and pull it through at the far end, bringing the wire with it.
By Gaspard Magalie. Motor Wiring. Published at Thursday, December 28th 2017, 10:08:52 AM. These are also known as canned motors. Two wires go into them. They often are directly connected to a battery. A switch turns them on. Higher voltages cause them to spin faster. Often geared down in toys, they are designed to spin fast. If turned on and forced to not spin, the motor will heat up, and may even burn up. The motor is made by copper wire covered with clear paint, and wound together in a ball. When the motor heats up too much, the paint turns into smoke, nearby copper wires connect, the motor becomes weaker, the motor heats up more, more smoke comes out, etc. The winding resistance keeps going down. Measure the winding resistance when the motor is new and measure again when there are problems.
By Olivier Constance. Electrical Wiring. Published at Thursday, December 28th 2017, 07:48:26 AM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By Fleurette Nina. Motor Wiring. Published at Thursday, December 28th 2017, 05:54:53 AM. Bipolar motors have a single winding per phase. The current in a winding needs to be reversed in order to reverse a magnetic pole, so the driving circuit must be more complicated, typically with an H-bridge arrangement "however there are several off-the-shelf driver chips available to make this a simple affair". There are two leads per phase, none are common.Static friction effects using an H-bridge have been observed with certain drive topologies.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.