By Cyrille Lothaire. Car Wiring. Publised at Saturday, July 08th 2017, 12:19:44 PM. Cable sizes are given by two numbers. The first one is the number of strands. The second (which is always the same in car wiring) is the diameter of each strand in millimetres. Twisting wires together and fitting spade terminals twist bare ends together and solder them.Cover the joint with insulating tape. Tag connectors are closedround the bare wire withpliers, then soldered. A spade terminal is easy to disconnect andreconnect. Methods of joining, wires To connect two wires, use a wire stripper to remove about in. (19 mm) of insulation from each wire.
By Fleurette Nina. Car Wiring. Published at Wednesday, August 30th 2017, 14:23:30 PM. STARTER SOLENOID "Relay" — All cars are wired so that the batterys main cable connects to the starter motor windings "the thick cable is needed for large current flow, right?". This wire must be switched on and off, of course, and it would be costly and inefficient to route it through the ignition switch "not to mention the size of the switchs components required to carry such current!". Consequently, a relay is necessary.
By France Barbara. Electrical Wiring. Published at Sunday, August 27th 2017, 10:48:35 AM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Olivier Constance. Electrical Wiring. Published at Thursday, August 24th 2017, 10:28:02 AM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
By Fleurette Nina. Electrical Wiring. Published at Saturday, August 19th 2017, 09:12:34 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Dorian Yannic. Electrical Wiring. Published at Wednesday, August 16th 2017, 08:13:28 AM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
By Dorian Yannic. Electrical Wiring. Published at Sunday, August 13th 2017, 05:49:48 AM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By Olivier Constance. Car Wiring. Published at Wednesday, August 09th 2017, 01:55:58 AM. Even if only one wire has overheated, inspect all the others to make sure their insulation is not damaged. Before cutting out damaged wires, make sure that the colour coding is the same at each end of the damaged section of each wire, and that it is not so discoloured that it is unrecognisable. If there is any chance of confusion, label both ends.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.