By Dorian Yannic. Car Wiring. Publised at Wednesday, November 15th 2017, 07:22:30 AM. Even if only one wire has overheated, inspect all the others to make sure their insulation is not damaged. Before cutting out damaged wires, make sure that the colour coding is the same at each end of the damaged section of each wire, and that it is not so discoloured that it is unrecognisable. If there is any chance of confusion, label both ends.
By Adrienne Emmanuel. Car Wiring. Published at Wednesday, September 27th 2017, 18:52:26 PM. The driven "or friction" plate runs on a splined input shaft, through which the power is transmitted to the gearbox. The plate has friction linings, similar to brake linings, on both its faces. This allows the drive to be taken up smoothly when the clutch is engaged. When the clutch is disengaged "pedal depressed", an arm pushes a release bearing against the centre of the diaphragm spring which releases the clamping pressure. The outer part of the pressure plate, which has a large friction surface, then no longer clamps the driven plate to the flywheel, so the transmission of power is interrupted and gears can be changed.
By Gaspard Magalie. Electrical Wiring. Published at Tuesday, September 26th 2017, 17:22:48 PM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 24th 2017, 00:10:58 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Adrienne Emmanuel. Motor Wiring. Published at Saturday, September 23rd 2017, 20:20:29 PM. Brushless outrunners are always built on a circuit board. This makes them cheaper. The circuit board for this CD motor has no electronics on it. A ribbon cable attaches 11 wires to another controller circuit board. But often the controller is built onto the same circuit board. The circuit boards interface with a controller in two ways.
By Fleurette Nina. Motor Wiring. Published at Thursday, September 21st 2017, 18:43:05 PM. The motor can be directly pulsed by the arduino. The arduino can also supply power to the motor, but normally this is only a good idea for demonstration purposes. The arduino has a very weak power supply, and attempting to power a motor through it can destroy the arduino. Furthermore, the arduino may not be able to supply the exact correct maximum voltage. For this reason, an ESC is placed between the arduino and the motor.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, September 17th 2017, 03:23:46 AM. digital signal processor is a specialized microprocessor for the kind of algorithms employed in digital signal processing (DSP). The main goal is to accelerate the calculations while keeping the power consumption as low as possible. In this article, we review a basic addressing capability of DSP processors, i.e. circular buffering, which allows us to significantly accelerate the data transfer in a real-time system. Please note that since the acronym “DSP” stands for both “digital signal processing” and “digital signal processor," we will use the term “DSP processor” when referring to the hardware rather than the algorithm.
By France Barbara. Electrical Wiring. Published at Saturday, September 16th 2017, 00:10:12 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.