By Mailys Laurent. Motor Wiring. Publised at Friday, January 05th 2018, 09:37:00 AM. An additional limitation, often comparable to the effects of inductance, is the back-EMF of the motor. As the motor rotor turns, a sinusoidal voltage is generated proportional to the speed (step rate). This AC voltage is subtracted from the voltage waveform available to induce a change in the current.
By Olivier Constance. Car Wiring. Published at Thursday, January 04th 2018, 06:05:59 AM. This system uses a metal wire embedded underneath the road as a guide for the battery powered vehicles. This wire is flexible enough to be used on straights, curves and hills. The vehicles are fitted with a motorised chassis and rechargeable battery which pushes the vehicle forwards via a small motor and gear arrangement, following the guide wire. The magnet offset to one side on the chassis is what activates the various additional modules (more on those later).
By Mailys Laurent. Electrical Wiring. Published at Thursday, January 04th 2018, 05:54:37 AM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Olivier Constance. Electrical Wiring. Published at Thursday, January 04th 2018, 04:04:27 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Fleurette Nina. Car Wiring. Published at Thursday, January 04th 2018, 01:54:35 AM. Spade terminal The spade terminal is theusual way of fixing wires to components. Crimp or bullet connector The crimpconnector is used for joining single wires toeach other. It may be a single or doubleconnector, or a multi- connector carryingseveral wires.
By Dorian Yannic. Car Wiring. Published at Thursday, January 04th 2018, 01:24:43 AM. Push a screwdriver blade through the grommet carefully to enlarge it for the new cables, taking care not to damage insulation on existing wires. If you pass a cable through a new hole, fit the hole with a grommet. To pass wires up door pillars or behind trim, tape them to a piece of fairly stiff wire, poke it carefully behind the trim or up the pillar, and pull it through at the far end, bringing the wire with it.
By Mailys Laurent. Motor Wiring. Published at Wednesday, January 03rd 2018, 23:58:29 PM. One way to distinguish the center tap (common wire) from a coil-end wire is by measuring the resistance. Resistance between common wire and coil-end wire is always half of the resistance between coil-end wires. This is because there is twice the length of coil between the ends and only half from center (common wire) to the end. A quick way to determine if the stepper motor is working is to short circuit every two pairs and try turning the shaft. Whenever a higher than normal resistance is felt, it indicates that the circuit to the particular winding is closed and that the phase is working.
By Fleurette Nina. Car Wiring. Published at Wednesday, January 03rd 2018, 15:37:45 PM. The damage caused by overheated wires is easy to find; but if only a single wire has overheated and melted at some point, you may have to use a circuit tester to find the break. If the damage is in an open run of wiring, you may be able to mend separate wires without taking out a section of the loom. If it is in any part of the covered sections, you need to remove at least part of the wiring loom.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.