By Gaspard Magalie. Car Wiring. Publised at Saturday, January 13th 2018, 16:46:32 PM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Dorian Yannic. Car Wiring. Publised at Tuesday, February 20th 2018, 09:35:38 AM. Cars are filled with stuff that can make or break performance. The engine needs to be fed the proper amounts of air, fuel, and spark. The suspension and brakes must be in tip-top shape. The wheels and tires, transmission, cooling system, gauges—even the seats—must all function properly.
By Gaspard Magalie. Car Wiring. Publised at Tuesday, February 20th 2018, 02:52:12 AM. Joins in individual wires are usually made with crimp connectors. The colour on the sleeve of a connector denotes the size of wire it will take. The bared ends of each wire are pushed into opposite ends of the metal-lined plastic sleeve, and squeezed with crimping pliers. There are multiple sleeves or other special connectors where a wire branches off.
By Dorian Yannic. Car Wiring. Published at Wednesday, November 15th 2017, 07:22:30 AM. The driven "or friction" plate runs on a splined input shaft, through which the power is transmitted to the gearbox. The plate has friction linings, similar to brake linings, on both its faces. This allows the drive to be taken up smoothly when the clutch is engaged. When the clutch is disengaged "pedal depressed", an arm pushes a release bearing against the centre of the diaphragm spring which releases the clamping pressure. The outer part of the pressure plate, which has a large friction surface, then no longer clamps the driven plate to the flywheel, so the transmission of power is interrupted and gears can be changed.
By France Barbara. Electrical Wiring. Published at Sunday, November 12th 2017, 22:18:25 PM. The tab-route or breakaway tab method is suitable for PCBs with either similar or different designs, or where it is not possible or practical to use the V-grooves. The designer leaves a perforated tabs routing space between the different or similar boards, hence allowing for separation after processing.
By Dorian Yannic. Electrical Wiring. Published at Saturday, November 11th 2017, 11:56:59 AM. digital signal processor is a specialized microprocessor for the kind of algorithms employed in digital signal processing (DSP). The main goal is to accelerate the calculations while keeping the power consumption as low as possible. In this article, we review a basic addressing capability of DSP processors, i.e. circular buffering, which allows us to significantly accelerate the data transfer in a real-time system. Please note that since the acronym “DSP” stands for both “digital signal processing” and “digital signal processor," we will use the term “DSP processor” when referring to the hardware rather than the algorithm.
By Dorian Yannic. Motor Wiring. Published at Friday, November 10th 2017, 03:07:38 AM. The two wires of the brushed dc motor can be thought of as forward and reverse. The three wires of brushless can be thought of as 1, 2 and 3. Going forward would be this sequence 1-2, 2-3, 3-1, 1-2, etc. Going backwards would be 1-3, 3-2, 2-1, 1-3, etc. What this means is that one third of the motor is helping maintain momentum while another third is pulling the motor in a new direction.
By France Barbara. Electrical Wiring. Published at Tuesday, November 07th 2017, 00:10:46 AM. The decoupling capacitors (C4, C5, C6, C7, C9, C10, C11) are arranged around the perimeter of the chip, very close to their respective power pins and to the vias that connect the caps to the internal planes. Notice how the smaller cap is always closer to the power pin; this is because we rely more on the lower-value capacitor for high-frequency bypassing, and thus the first priority is minimizing the inductance and resistance between the smaller cap and the pin.
By Gaspard Magalie. Motor Wiring. Published at Monday, November 06th 2017, 04:29:01 AM. Brushless outrunners are always built on a circuit board. This makes them cheaper. The circuit board for this CD motor has no electronics on it. A ribbon cable attaches 11 wires to another controller circuit board. But often the controller is built onto the same circuit board. The circuit boards interface with a controller in two ways.
By Olivier Constance. Electrical Wiring. Published at Thursday, November 02nd 2017, 20:16:28 PM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.