By Cyrille Lothaire. Electrical Wiring. Publised at Thursday, December 28th 2017, 05:00:05 AM. As you may have noticed, this is one of those annoying situations in which the pin configuration is the opposite of what you want: the DAC’s input pins move from bit 7 to bit 0 going downward, whereas the MCU’s output pins move from bit 7 to bit 0 going upward. I couldn’t remedy this by re-assigning the microcontroller pins because I wanted the data bits to correspond to the actual bits of the Port 2 register (so that I could write a full byte to the DAC without moving bits around). So I ended up with some awkward routing, but nothing terrible.
By France Barbara. Car Wiring. Published at Friday, January 12th 2018, 02:10:06 AM. Cut out all the damaged wires with wire cutters. Spread out the cuts across a bundle of several wires: if many joins are opposite each other their bulk may make it difficult to fit the loom into the car. If possible, replace wiring with new wire of the same colour. The new wire must be the right size: there are five sizes, depending on current rating. Repairs in wrapped sections of the loom are the only places where you may join wires by twisting them together and soldering the joint mainly because there may not be room for any other method.
By Fleurette Nina. Electrical Wiring. Published at Thursday, January 11th 2018, 23:55:36 PM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Olivier Constance. Electrical Wiring. Published at Thursday, January 11th 2018, 21:05:01 PM. Manufacturers can use fixtures or panels to secure or frame fragile, thin, or oddly shaped PCBs. This allows them to easily fit the boards in the standard assembly, reflow, or automatic inspection machines. In addition to handling the irregular boards, the technologies enable the simultaneous processing of multiple boards as opposed to working on each board individually, hence reducing the production time and costs.
By Mailys Laurent. Motor Wiring. Published at Thursday, January 11th 2018, 08:55:14 AM. 2 wires. Servomechanisms are designed to move to a spot and hold it is position. They are not designed to spin continuously. Used to position print heads in ink jet printers, plotters, scanners. Travel at set speeds. Go to a spot and stop. When stopped and still turned on, will attempt to hold it is position. Forcing it to move in this position can damage the motor. Typically is controlled by a circuit board that counts shadows with an LED and light sensor or has a resistor that changes value depending upon position. Often zooms to one side when powered on to figure out where it is at.
By Claudine Nicolette. Motor Wiring. Published at Thursday, January 11th 2018, 07:00:17 AM. After the retaining ring is removed, the entire assembly that spins can be removed. There may be some resistance that feels like removing magnets from each other. Underneath the cup of all outrunner brushless motors is a series of coils. On some motors, between the coils, are hall effect probes. Hall effect probes detect the spinning magnetic field and provide a pulse out of the brushless motors to the electronics. From this pulse the electronics can precisely control the speed of the motor
By Mailys Laurent. Electrical Wiring. Published at Thursday, January 11th 2018, 06:19:01 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Mailys Laurent. Car Wiring. Published at Thursday, January 11th 2018, 06:17:26 AM. The electrical wiring in a car is a system of colour-coded wires called the loom. Where several wires run side by side they are bound together with insulating tape or plastic sleeving.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.