By Fleurette Nina. Car Wiring. Publised at Wednesday, January 17th 2018, 22:00:03 PM. Label wires before cutting them when working on a section of the loom. Before you disconnect anything, make absolutely sure you know how to put it back. Number both sides of each connection with labels made of masking tape. If necessary, make drawings of cable routes and how clips fit. Use a craft knife or razor blade to cut away the wrapping from the damaged section. Take care not to cut into the plastic cable insulation.
By Dorian Yannic. Electrical Wiring. Published at Wednesday, November 22nd 2017, 13:04:57 PM. The datasheet states (see image below) that this IC—specifically the CMOSens® technology that it uses—is "designed for mass production." Umm, should not this go without saying? I have seen datasheets state "not recommended for new designs," but I do not ever recall seeing one that specifies that the IC, or its underlying technology, is designed for mass production. This benefit makes me question if Sensirion has other ICs that are in fact not designed for mass production. It is all a bit puzzling. Have you seen other IC datasheets call this out? If so, please let us know.
By Adrienne Emmanuel. Car Wiring. Published at Friday, November 17th 2017, 02:23:17 AM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Dorian Yannic. Car Wiring. Published at Wednesday, November 15th 2017, 07:22:30 AM. Push the wire into the connector so that the strands just protrude from the round end. Grip the cable, connector uppermost, in a vice or self-locking pliers, so that the connector rests on top of the vice and cannot slide down the wire when soldering. Inside a bullet connector. Apply solder on the top of the connector, and let it melt and run down inside. Trim off the protruding strands with wire cutters.
By France Barbara. Electrical Wiring. Published at Sunday, November 12th 2017, 22:18:25 PM. Since the finite-impulse-response (FIR) filtering is a common operation in DSP, we will continue our discussion based on examining the difference equation of an FIR filter. This simple example will show the typical properties of many DSP algorithms. After reviewing the problem of handling the incoming samples, we will discuss the circular buffering as an efficient solution to the problem.
By Dorian Yannic. Electrical Wiring. Published at Saturday, November 11th 2017, 11:56:59 AM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By Dorian Yannic. Motor Wiring. Published at Friday, November 10th 2017, 03:07:38 AM. Stepper motor performance is strongly dependent on the driver circuit. Torque curves may be extended to greater speeds if the stator poles can be reversed more quickly, the limiting factor being a combination of the winding inductance. To overcome the inductance and switch the windings quickly, one must increase the drive voltage. This leads further to the necessity of limiting the current that these high voltages may otherwise induce.
By France Barbara. Electrical Wiring. Published at Tuesday, November 07th 2017, 00:10:46 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.