By Adrienne Emmanuel. Car Wiring. Publised at Friday, January 12th 2018, 07:38:14 AM. It is commonly known as the BENDIX type of solenoid. Such solenoids operate in three stages, the disengaged, partially engaged and engaged. In the disengaged position the drive gear is released and no current is flowing. In the partially engaged stage, current from the starter switch flows through both the pull-in and the hold-in coils.
By Mailys Laurent. Electrical Wiring. Published at Saturday, December 30th 2017, 21:23:01 PM. Manual removal of the tabs depends on the design and thickness of the board. Extra care is required since using some tools such as the hook-shaped blade to break the solid tabs between the boards can be challenging and inefficient. For example, if the blade rotates within the small clearance between the boards, it can easily take a bite out of the useful part of the PCB. Also, taping the blade-cutting edge leaves a small part of the tab protruding from the board.
By Olivier Constance. Electrical Wiring. Published at Saturday, December 30th 2017, 19:12:00 PM. PCBs with SMT on both sides and those with mixed TH and SMTs may start to flex and bow when in the reflow oven or selective soldering machine. For this reason, the maximum size for this type of board is usually smaller than the single-sided. Breaking out the boards manually can stress the board and components near the edges, the solder joints, or leave out rough stubs on the edges
By Dorian Yannic. Motor Wiring. Published at Saturday, December 30th 2017, 17:51:58 PM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
By Claudine Nicolette. Car Wiring. Published at Saturday, December 30th 2017, 16:22:53 PM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Fleurette Nina. Car Wiring. Published at Saturday, December 30th 2017, 15:34:30 PM. Relays are devices that utilize a central iron core fitted closely to the inside of a coil of wire. When the wire is energized the iron core will be drawn down the length of the coil, the direction dependent upon the direction of current flow. If the relays iron core is fitted with large, high current-carrying contacts it can be used as a high-current switch. Relays are used throughout cars for horns, electric fans, air conditioning clutches, etc. and the most important one is the starter solenoid.
By Gaspard Magalie. Motor Wiring. Published at Saturday, December 30th 2017, 13:07:39 PM. 2 wires. Servomechanisms are designed to move to a spot and hold it is position. They are not designed to spin continuously. Used to position print heads in ink jet printers, plotters, scanners. Travel at set speeds. Go to a spot and stop. When stopped and still turned on, will attempt to hold it is position. Forcing it to move in this position can damage the motor. Typically is controlled by a circuit board that counts shadows with an LED and light sensor or has a resistor that changes value depending upon position. Often zooms to one side when powered on to figure out where it is at.
By Fleurette Nina. Electrical Wiring. Published at Saturday, December 30th 2017, 11:42:26 AM. In a demanding application, we may not have the time to continuously check the pointers to see if they have reached the end of the buffer and wrap them back to the beginning of the buffer when necessary. As a result, a DSP processor uses dedicated hardware to provide some fast circular buffers.This hardware implementation automatically checks the status of the pointers and updates them accordingly.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.