By Adrienne Emmanuel. Car Wiring. Publised at Friday, January 12th 2018, 07:38:14 AM. To fit a spade terminal, slip the insulating cover over the wire and push it up the wire, out of the way. Use a wire stripper to remove about 1/8in. (3 mm) of insulation from the end of the wire. Lay the bare strands in the inner section of the connector. Use crimping pliers to tighten the two small tongues firmly around the insulated part of the wire. On the other side of the connector, push the wire strands back and down flat. Hold the connector blade upwards to avoid solder running into the spade part.
By Cyrille Lothaire. Electrical Wiring. Published at Monday, January 01st 2018, 10:24:51 AM. Care should be taken when depaneling the perforated-tab PCB array; otherwise, an incorrect method will splinter or tear the solder-mask or active surface layer. The ideal breakout method should not cause any damage to the board or transfer stress from the PCB surface to the components.
By Gaspard Magalie. Electrical Wiring. Published at Monday, January 01st 2018, 07:06:16 AM. In a demanding application, we may not have the time to continuously check the pointers to see if they have reached the end of the buffer and wrap them back to the beginning of the buffer when necessary. As a result, a DSP processor uses dedicated hardware to provide some fast circular buffers.This hardware implementation automatically checks the status of the pointers and updates them accordingly.
By Adrienne Emmanuel. Electrical Wiring. Published at Monday, January 01st 2018, 05:49:16 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Fleurette Nina. Electrical Wiring. Published at Monday, January 01st 2018, 02:25:46 AM. Processing irregular and fragile PCBs in standard assembly machines is often a challenge. Due to their non-standard dimensions, the oddly shaped, thin, or fragile boards do not fit properly in the reflow, component placement, or other standard processing machines. Lack of adequate support and alignment may strain, bend or damage the fragile boards as they go through the processing system. In addition, this may impact the accuracy of the process.
By Fleurette Nina. Motor Wiring. Published at Monday, January 01st 2018, 01:13:26 AM. They are not controlled through a circuit board or ESC. They have to be connected to the arduino through a motor shield or custom built circuit. They are typically the most expensive. Stepper motors can have 4, 5, 6, or 8 wires. To use them with the arduino, understanding the internal wiring is absolutely necessary. The best way to learn the internal wiring is to assume no manual exists, and "discover" the internal wiring.
By France Barbara. Car Wiring. Published at Monday, January 01st 2018, 00:11:54 AM. With all those things to worry about, many enthusiasts overlook the electrical wiring system. A lousy wiring job will keep your electrical accessories from operating at full potential—and that means subpar performance. Many people are intimidated by the prospect of wiring a vehicle. But a proper wiring job doesn’t have to be a scary task—we’ve put together a few tips to help make the job a little bit smoother.
By Mailys Laurent. Motor Wiring. Published at Sunday, December 31st 2017, 23:11:28 PM. One way to distinguish the center tap (common wire) from a coil-end wire is by measuring the resistance. Resistance between common wire and coil-end wire is always half of the resistance between coil-end wires. This is because there is twice the length of coil between the ends and only half from center (common wire) to the end. A quick way to determine if the stepper motor is working is to short circuit every two pairs and try turning the shaft. Whenever a higher than normal resistance is felt, it indicates that the circuit to the particular winding is closed and that the phase is working.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.