By Adrienne Emmanuel. Car Wiring. Publised at Friday, January 12th 2018, 07:38:14 AM. Spade terminal The spade terminal is theusual way of fixing wires to components. Crimp or bullet connector The crimpconnector is used for joining single wires toeach other. It may be a single or doubleconnector, or a multi- connector carryingseveral wires.
By Cyrille Lothaire. Motor Wiring. Published at Tuesday, January 02nd 2018, 14:41:34 PM. Speed can be varied by either changing the voltage or pulsing the motor. Most computer controlled DC motors are pulsed. Pulses of a fixed voltage are sent to the motor, usually by an Electronic Speed Controller or ESC. A pulse of 1.5 ms causes no motion. Wider pulses cause faster spinning in one direction. Shorter pulses cause faster spinning in the opposite direction. Eventually, an overstressed ESC stops pulsing and turns one wire on and one wire off, depending on the direction.
By Claudine Nicolette. Car Wiring. Published at Monday, January 01st 2018, 13:12:01 PM. Several modern cars have separate thin wires embedded in flat plastic strips. These strips are very compact, and are used mainly for accessories and relay controls that require little power.
By Adrienne Emmanuel. Electrical Wiring. Published at Monday, January 01st 2018, 12:49:27 PM. The decoupling capacitors (C4, C5, C6, C7, C9, C10, C11) are arranged around the perimeter of the chip, very close to their respective power pins and to the vias that connect the caps to the internal planes. Notice how the smaller cap is always closer to the power pin; this is because we rely more on the lower-value capacitor for high-frequency bypassing, and thus the first priority is minimizing the inductance and resistance between the smaller cap and the pin.
By Mailys Laurent. Electrical Wiring. Published at Monday, January 01st 2018, 12:00:38 PM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Olivier Constance. Car Wiring. Published at Monday, January 01st 2018, 11:51:08 AM. Cable sizes are given by two numbers. The first one is the number of strands. The second (which is always the same in car wiring) is the diameter of each strand in millimetres. Twisting wires together and fitting spade terminals twist bare ends together and solder them.Cover the joint with insulating tape. Tag connectors are closedround the bare wire withpliers, then soldered. A spade terminal is easy to disconnect andreconnect. Methods of joining, wires To connect two wires, use a wire stripper to remove about in. (19 mm) of insulation from each wire.
By Cyrille Lothaire. Electrical Wiring. Published at Monday, January 01st 2018, 10:24:51 AM. Note that U4, a 10 MHz MEMS oscillator, is also very close to the microcontroller’s clock input pin. It’s always a good idea to minimize the length of traces carrying high-frequency digital signals. First of all, there are noise benefits: a shorter, more direct trace reduces the amount of noise that would otherwise be coupled into adjacent traces, and a shorter trace also reduces electromagnetic interference (EMI) because it is less effective as an antenna. The second issue is related to transmission-line effects. Minimizing trace length is a simple way to avoid problems related to signal reflections. However, reflection is not a significant concern at frequencies in the 10 MHz range, unless you are dealing with long interconnections or a very large PCB.
By Gaspard Magalie. Electrical Wiring. Published at Monday, January 01st 2018, 07:06:16 AM. Depanelization is the process of separating the individual boards from the main array and usually depends on the panelization method applied. The choice depends on the clearance to provide at the edges of the PCB, and the presence of sensitive SMT devices, or hanging connectors near the edges. There are automatic methods, such as the laser cutting or depaneling router, as well as manual methods that involve breaking the tabs using hands or other tools.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.