By Cyrille Lothaire. Car Wiring. Publised at Saturday, July 08th 2017, 12:19:44 PM. If possible, use an insulated in-line crimp connector. Test each mended wire with a circuit tester and battery, connected to the nearest connectors either side of the mend. Re-wrap the exposed section of the loom with self-adhesive or "clingfilm" PVC insulating tape. Put some layers between the exposed section and adjoining wires - not merely a cover over the top - then fit the loom back into the car. Reconnect all terminals and clips, then test all the electrical components involved.
By Cyrille Lothaire. Motor Wiring. Published at Saturday, September 09th 2017, 08:13:56 AM. A stepper motor is a polyphase AC synchronous motor (see Theory below), and it is ideally driven by sinusoidal current. A full-step waveform is a gross approximation of a sinusoid, and is the reason why the motor exhibits so much vibration. Various drive techniques have been developed to better approximate a sinusoidal drive waveform: these are half stepping and microstepping.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, September 06th 2017, 04:45:11 AM. Panelization is the arranging of arrays of multiple PCBs onto a single substrate that fits in the standard processing machine. A panel may hold multiple boards with similar or different sizes and shapes. This method is faster and less costly compared to the fixtures, which require a custom carrier for every new PCB design.
By Mailys Laurent. Electrical Wiring. Published at Tuesday, September 05th 2017, 03:51:19 AM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Dorian Yannic. Electrical Wiring. Published at Saturday, September 02nd 2017, 03:47:50 AM. The datasheet goes on to say that "the nRESET pin is internally connected to VDD with a pull up resistor of 50 kΩ." So... why are there two options for how to configure the nReset pin when it is not being used? Why not just recommend that it should be left floating (since it is already pulled high internally)? And, if there are indeed technical reasons for when the pin should be externally pulled up to VDD (for better noise immunity, as an example) then let us know what those technical reasons are.
By Olivier Constance. Electrical Wiring. Published at Thursday, August 31st 2017, 15:24:12 PM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Fleurette Nina. Car Wiring. Published at Wednesday, August 30th 2017, 14:23:30 PM. With all those things to worry about, many enthusiasts overlook the electrical wiring system. A lousy wiring job will keep your electrical accessories from operating at full potential—and that means subpar performance. Many people are intimidated by the prospect of wiring a vehicle. But a proper wiring job doesn’t have to be a scary task—we’ve put together a few tips to help make the job a little bit smoother.
By France Barbara. Electrical Wiring. Published at Sunday, August 27th 2017, 10:48:35 AM. The decoupling capacitors (C4, C5, C6, C7, C9, C10, C11) are arranged around the perimeter of the chip, very close to their respective power pins and to the vias that connect the caps to the internal planes. Notice how the smaller cap is always closer to the power pin; this is because we rely more on the lower-value capacitor for high-frequency bypassing, and thus the first priority is minimizing the inductance and resistance between the smaller cap and the pin.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.