By Cyrille Lothaire. Car Wiring. Publised at Tuesday, January 09th 2018, 14:11:38 PM. If this does not blow a fuse the wiring overheats and melts insulation, perhaps starting a fire. A similar result can come from fitting accessories incorrectly, or if power demand is too high for the size of the wire being used. After many years, insulation may become hard and brittle, particularly where it is exposed to heat, as in the engine bay. Sections, or all of the loom, may need replacing.
By Cyrille Lothaire. Car Wiring. Publised at Monday, June 26th 2017, 01:19:39 AM. Starter motors fail mostly due to overheating. They are placed in a hostile, hot environment and cannot be expected to last indefinitely. Another mode of failure is a shorted or open winding. This exhibits itself as a "dead spot" on the commutator. If a brush lands on a dead spot the motor wont turn at all. A third failure-mode is a faulty pinion engagement. Sometimes the pinion assembly gets stiff or stuck due to lack of lubrication or wear. Starter motor rebuilding or replacement is required for all of these problems.
By Adrienne Emmanuel. Car Wiring. Publised at Wednesday, September 27th 2017, 18:52:26 PM. The starter solenoid has very large contacts to carry the batterys full current. Its wire coil is actuated by a smaller current from the ignition switch, at which time the iron core slams down to make contact and turn on the starter motor. Most non-Ford starter motors employ a solenoid built into the motor itself. This type of solenoid not only provides the motors electrical power but also mechanically engages the starters drive gear onto the flywheel.
By Fleurette Nina. Motor Wiring. Published at Thursday, February 22nd 2018, 01:17:06 AM. RC servos are used to provide actuation for various mechanical systems such as the steering of a car, the control surfaces on a plane, or the rudder of a boat. Due to their affordability, reliability, and simplicity of control by microprocessors, they are often used in small-scale robotics applications. A standard RC receiver (or a microcontroller) sends pulse-width modulation (PWM) signals to the servo. The electronics inside the servo translate the width of the pulse into a position. When the servo is commanded to rotate, the motor is powered until the potentiometer reaches the value corresponding to the commanded position.
By Claudine Nicolette. Electrical Wiring. Published at Wednesday, February 21st 2018, 18:29:47 PM. This PCB, like almost all of my PCBs, is a four-layer board. In my opinion, it is not wise to restrict yourself to two layers unless you’re dealing with a very simple circuit or you really need to cut costs. The four-layer arrangement is beneficial in terms of routing and performance: routing, because via connections to internal planes almost completely eliminate power and ground traces; and performance, because the internal planes allow for low-resistance, low-inductance power and ground connections. The extra top-layer and bottom-layer real estate opened up by all the internal-plane connections come in very handy when you need to provide a generous copper area for improved thermal performance (for example, to make sure that your LDO or your motor driver doesn’t overheat and enter thermal shutdown).
By Adrienne Emmanuel. Electrical Wiring. Published at Wednesday, February 21st 2018, 03:38:10 AM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By France Barbara. Electrical Wiring. Published at Tuesday, February 20th 2018, 23:10:55 PM. Generally, the fixture materials, which range from synthetic plastics and stones to aluminum alloys and epoxy glass, should be electrostatic neutral, and able to withstand repeated thermal cycles and chemicals without deforming or wear. In particular, the thin fixtures provide better thermal management.
By Dorian Yannic. Car Wiring. Published at Tuesday, February 20th 2018, 09:35:38 AM. Push a screwdriver blade through the grommet carefully to enlarge it for the new cables, taking care not to damage insulation on existing wires. If you pass a cable through a new hole, fit the hole with a grommet. To pass wires up door pillars or behind trim, tape them to a piece of fairly stiff wire, poke it carefully behind the trim or up the pillar, and pull it through at the far end, bringing the wire with it.
By Cyrille Lothaire. Motor Wiring. Published at Tuesday, February 20th 2018, 06:15:41 AM. A unipolar stepper motor has one winding with center tap per phase. Each section of windings is switched on for each direction of magnetic field. Since in this arrangement a magnetic pole can be reversed without switching the direction of current, the commutation circuit can be made very simple (e.g., a single transistor) for each winding. Typically, given a phase, the center tap of each winding is made common: giving three leads per phase and six leads for a typical two phase motor. Often, these two phase commons are internally joined, so the motor has only five leads.
By Mailys Laurent. Electrical Wiring. Published at Tuesday, February 20th 2018, 03:43:49 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.