By Fleurette Nina. Car Wiring. Publised at Saturday, January 06th 2018, 13:05:48 PM. Solder the wire to the connector with just enough solder to secure all the strands. Let the connector cool before sliding the cover back. Fitting a bullet connector. Remove insulation with a wire stripper. Use a wire stripper to remove about 3/8 in. (10 mm) of insulation from the end of the wire.
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 10th 2017, 02:36:22 AM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Claudine Nicolette. Motor Wiring. Published at Saturday, October 07th 2017, 00:23:28 AM. It appears to be falling apart like a vacuum cleaner motor. You do not need to tear these apart. Look at these wikicommons pictures. Taking apart a CD player and finding the motor is fairly easy.Start by turning it upside down and removing the screws holding the bottom plate on.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, October 04th 2017, 00:20:15 AM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Mailys Laurent. Electrical Wiring. Published at Monday, October 02nd 2017, 21:00:02 PM. Sensirion provides detailed information on both the package outline and the land pattern. In fact, it is recommended, because the IC pad pitch is just 0.5 mm, that only one solder mask opening should be used for all four pads on one side. It is also suggested, when using solder paste printing, that a laser-cut stainless steel stencil with trapezoidal walls and with a stencil thickness of 0.1 or 0.125 mm should be used. See the images below. This information should be quite helpful for a PCB layout design team.
By Cyrille Lothaire. Electrical Wiring. Published at Sunday, October 01st 2017, 20:21:48 PM. It’s always good to be cognizant of trace lengths when you’re laying out a parallel bus, though at moderate frequencies it is nothing to stress about. The propagation time for a signal traveling through a trace is maybe 150 picoseconds/inch. So if you have two traces with a length mismatch of one inch, one signal will arrive 150 ps after the other signal. If your signals are transitioning at a frequency whose corresponding period is much greater than 150 ps, this one-inch mismatch won’t cause problems. Even at 100 MHz (which is pretty fast for a parallel bus), the period is 10 ns, i.e., ~67 times larger than the time-of-arrival discrepancy for a one-inch mismatch.
By Dorian Yannic. Electrical Wiring. Published at Saturday, September 30th 2017, 19:13:18 PM. The tab-route or breakaway tab method is suitable for PCBs with either similar or different designs, or where it is not possible or practical to use the V-grooves. The designer leaves a perforated tabs routing space between the different or similar boards, hence allowing for separation after processing.
By Adrienne Emmanuel. Car Wiring. Published at Wednesday, September 27th 2017, 18:52:26 PM. If possible, use an insulated in-line crimp connector. Test each mended wire with a circuit tester and battery, connected to the nearest connectors either side of the mend. Re-wrap the exposed section of the loom with self-adhesive or "clingfilm" PVC insulating tape. Put some layers between the exposed section and adjoining wires - not merely a cover over the top - then fit the loom back into the car. Reconnect all terminals and clips, then test all the electrical components involved.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.