By Olivier Constance. Car Wiring. Publised at Thursday, December 28th 2017, 10:09:08 AM. Even if only one wire has overheated, inspect all the others to make sure their insulation is not damaged. Before cutting out damaged wires, make sure that the colour coding is the same at each end of the damaged section of each wire, and that it is not so discoloured that it is unrecognisable. If there is any chance of confusion, label both ends.
By Claudine Nicolette. Car Wiring. Published at Friday, October 20th 2017, 09:41:36 AM. Also look for grommets that have come out of their holes. The sharp edge of the hole will soon chafe through wire insulation and cause a short circuit. Whenever you pull a connection apart, look for corrosion which might cause bad contact. If necessary, clean contacting metal surfaces with a fine file or emery cloth.
By Adrienne Emmanuel. Motor Wiring. Published at Tuesday, October 17th 2017, 09:01:49 AM. Brushed DC motors rotate continuously when DC voltage is applied to their terminals. The stepper motor is known by its property to convert a train of input pulses (typically square wave pulses) into a precisely defined increment in the shaft position. Each pulse moves the shaft through a fixed angle. Stepper motors effectively have multiple "toothed" electromagnets arranged around a central gear-shaped piece of iron. The electromagnets are energized by an external driver circuit or a micro controller. To make the motor shaft turn, first, one electromagnet is given power, which magnetically attracts the gear teeth. When the gear teeth are aligned to the first electromagnet, they are slightly offset from the next electromagnet.
By Fleurette Nina. Electrical Wiring. Published at Thursday, October 12th 2017, 05:54:44 AM. The fixtures are usually available in a variety of designs, materials, sizes, and thicknesses. Some can carry more than one board hence allowing the processing of multiple PCBs simultaneously. Other designs have adjustments to support both the primary and secondary side processes.
By Dorian Yannic. Electrical Wiring. Published at Tuesday, October 10th 2017, 02:36:22 AM. There are different panelization and de-panelization methods depending on the application of the PCB, thickness, shape, component layout, type of edges, and other factors. The two popular methods are the V-groove panelization and the breakaway tab panelization. Each of these uses a different method to separate the boards from the main array and has its advantages and limitations.
By Claudine Nicolette. Motor Wiring. Published at Saturday, October 07th 2017, 00:23:28 AM. The arduino sends pulses to the servo motor much like sending them to an ESC. The pulses have a different meaning. The pulses describe a spot to go to. Within the servo there is a feedback mechanism that counts shadows or turns a variable resistor. The servo circuit board then moves the servo to that spot. It knows when it has reached the spot when a certain number of shadows have past or when the resistance reaches a certain value. The arduino has to keep sending the same position over and over again to hold the motor in a current spot. Short pulses go one direction, long pulses the opposite direction, medium pulse widths go to the middle. Middle is typically 1.5 milli seconds.
By Cyrille Lothaire. Electrical Wiring. Published at Wednesday, October 04th 2017, 00:20:15 AM. When implementing a real-time system, we find a circular buffer critical whether we are using a DSP processor or a general purpose processor (GPP). However, with a GPP we may have to implement the circular buffer in software. As discussed in the previous section, with each new sample, we have to update the pointer which contains the address of the newest sample. With a circular buffer implemented in software, the programmer needs to take care of updating the buffer pointers after each read and write operation. When the pointer reaches the end of the buffer, the program must wrap the pointer back to the beginning of the buffer.
By Mailys Laurent. Electrical Wiring. Published at Monday, October 02nd 2017, 21:00:02 PM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.