By Olivier Constance. Car Wiring. Publised at Thursday, December 28th 2017, 10:09:08 AM. Label wires before cutting them when working on a section of the loom. Before you disconnect anything, make absolutely sure you know how to put it back. Number both sides of each connection with labels made of masking tape. If necessary, make drawings of cable routes and how clips fit. Use a craft knife or razor blade to cut away the wrapping from the damaged section. Take care not to cut into the plastic cable insulation.
By Gaspard Magalie. Electrical Wiring. Published at Friday, December 29th 2017, 23:04:12 PM. I always prefer to maintain a logical flow of signals and functionality in my PCB layouts. I think that this approach results in an easier design process and a better board. The AWG layout progresses from left to right: from power input and communication input/output, to the power supply circuitry, to the processor, to the DAC (which is controlled by the processor and constitutes the board’s transition from digital to analog), to the analog signal-conditioning circuitry, and finally to the output connector. Parts that don’t have a specific position in the functional flow—such as the oscillator (U4), the DAC’s passives (C16, R5, etc.), and the voltage reference (U3)—are arranged near the components that they support.
By Claudine Nicolette. Electrical Wiring. Published at Friday, December 29th 2017, 20:19:29 PM. Reset pin may be used to generate a system reset of the IC. And while a reset may also be externally generated by issuing a command (referred to as a soft reset), to achieve a full reset it is recommended to use the nReset pin (or of course you can also cycle power). On the other hand, if this pin is not to be used then it is recommended that it is either left floating or tied to VDD via a series resistor of value ≥2 kΩ.
By Adrienne Emmanuel. Electrical Wiring. Published at Friday, December 29th 2017, 20:12:23 PM. The fixture should support the board and prevent distortion as the board goes through the printing, component placement, and reflow processes. Its construction should ensure adequate protection for the bottom side components during the double-sided reflow process.
By Dorian Yannic. Electrical Wiring. Published at Friday, December 29th 2017, 15:30:43 PM. You can also see that I’ve made it very easy for heat to move away from the regulator (U1) and into the ambient environment or into other portions of the PCB. U1’s thermal tab is connected to a large copper pour, and this copper pour is shot through with vias that conduct heat down to the internal ground plane. If I were really worried about thermal issues I could also connect these vias to a copper pour on the bottom side of the board, but in this case, it would have been total overkill.
By Mailys Laurent. Electrical Wiring. Published at Friday, December 29th 2017, 09:43:55 AM. V-groove panelization involves cutting a third of the board’s thickness from the top and bottom sides. The remaining part joins the separate boards and is then cut with a machine during the depaneling. This helps to reduce the stress on the PCB. One challenge with the V-groove method is that it is restrictive and cannot be used with PCBs that have overhanging components over the edges.
By Fleurette Nina. Motor Wiring. Published at Friday, December 29th 2017, 08:52:17 AM. Electronic motors are found in kids toys, RC cars, airplanes and helicopters, printers, scanners, and fax machines. They are expensive when purchased, quantity 1, new with manual. This is because the motors are part of a supply chain that is usually just making enough to fill orders for kids toys, etc. Many can be found for sale on the internet, but very few are in stock and the price is high if they are. Often it is easier to purchase the kids toy and take it apart. The goal is to connect these motors to the arduino and then make something new with them. The goal of this document is to describe what to expect.
By Dorian Yannic. Motor Wiring. Published at Friday, December 29th 2017, 07:22:49 AM. The arduino sends pulses to the servo motor much like sending them to an ESC. The pulses have a different meaning. The pulses describe a spot to go to. Within the servo there is a feedback mechanism that counts shadows or turns a variable resistor. The servo circuit board then moves the servo to that spot. It knows when it has reached the spot when a certain number of shadows have past or when the resistance reaches a certain value. The arduino has to keep sending the same position over and over again to hold the motor in a current spot. Short pulses go one direction, long pulses the opposite direction, medium pulse widths go to the middle. Middle is typically 1.5 milli seconds.
Nolanwebdev - Wiring Diagram Images Collection
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.